This content is not included in your SAE MOBILUS subscription, or you are not logged in.
Nondestructive Estimation of Resistance of Tire Construction to Tread Wear
ISSN: 0148-7191, e-ISSN: 2688-3627
Published January 01, 1963 by SAE International in United States
Annotation ability available
Conventionally, tires are made with cross-bias cases. In Europe, however, there is increasing interest in other constructions that enable vibration characteristics to be chosen to suit the vibration transmission characteristics of the vehicle. Since construction is an important factor in controlling tread wear, an estimate must be made when initial information about vibration is available, so that unprofitable designs will be given low priority. This paper summarizes the nondestructive techniques used in estimating tread wear resistance of various tire constructions, both in the laboratory and on the drawing board.
|Technical Paper||Ply Steer in Radial Carcass Tires|
|Technical Paper||Control-Oriented Modeling of a Vehicle Drivetrain for Shuffle and Clunk Mitigation|
|Technical Paper||On the Design of a Low Vibration Helical Gear for Automobiles|
CitationGough, V., "Nondestructive Estimation of Resistance of Tire Construction to Tread Wear," SAE Technical Paper 630181, 1963, https://doi.org/10.4271/630181.
- Williams J. I. S. and Clifton, R. G. “Pneumatic Tire Testing.” Proc. Third Rubber Technology Conference, Institution of Rubber Industry, London (1954), p. 512.
- Roberts, G. B. “Power Wastage in Tires.” Proc. International Rubber Conference (November, 1954) American Chemical Society, Washington, D. C, p. 57.
- Symposium on Research in Automobile Stability and Control in Tyre Performance, Proc. Automobile Division IME (1955–1956): Milliken W. F. and Whitcomb, D. W. “General Introduction to a Programme of Dynamic Research,” p. 287 Segel, L. “Theoretical Prediction and Experimental Substantiation of the Response of the Automobile to Steering Control,” p. 310 Close W. and Muzzey, C. L, “A Device for Measuring Mechanical Characteristics of Types on the Road,” p. 331 Fonda, A. G. “Tyre Tests and Interpretation of Experimental Data,” p. 348 Whitcomb D. W. and Milliken, W. F. “Design Implication of a General Theory of Automobile Stability and Control,” p. 367.
- Gough V. E. and French, T. “Tyres and Skidding from a European Viewpoint.” Proc. First International Skid Prevention Conference U. S. A. (August, 1959) p. 189.
- Gough V. E. and Whitehall, S. G. “Universal Tyre Test Machine.” Ninth International Automobile Technical Congress (1962).
- Herzegh, F. “A Method of Measuring Thump and Roughness for Quality Control of Passengers Car Tire Production.” Paper presented to SAE, June, 1957.
- Radt, H. S. “Mechanism of Tire Thump and Roughness.” Paper 322C presented to SAE, March, 1961.
- Lippman, S. A. “Forces and Torques Associated with Roughness in Tires.” Paper 322D presented to SAE, March, 1961.
- Morrish L. M. and Haust, R. R. “Effect of Loaded Radial Runout on Tire Roughness and Shake.” Paper 322E presented to SAE, March, 1961.
- Liska J. W. and Sidles, J. “Tyre Dynamics Effect on Noise and Vibration.” Paper 322F presented to SAE, March, 1961.
- Anderson, M. G. “Tire Uniformity.” Paper 322B presented to SAE, March, 1961.
- Gough, V. E. Barson, C. W. Gough S. W. and Bennett, W. D. “Tire Uniformity Grading Machine.” Paper 322A presented to SAE, March, 1961 (also published in Engineer, April 26, 1962).
- Chiesa, A. “Vehicle Vertical Vibration and Tire Performance.” Paper 490C presented to SAE, March, 1962.
- Gough, V. E. Hardman, J. H. and Maclaren, J. R. “A-braded Tyre Treads.” Trans. Institution of Rubber Industry, Vol. 32 (1956), p. 27.
- Gough V. E. and Shearer, G. R. “Front Suspension and Tyre Wear of Automobile Division.” IME (1955–1956), p. 171.
- Ginn, J. L. Marlowe, R. L. and Miller, R. F. “Tread Wear Indexes of Various Synthetic Elastomers Measured in Varying Seventy Road Tests.” Second International Synthetic Rubber Symposium, London, October, 1960; also, Rubber & Plastics Age, Vol. 42, No. 8 (1961), p. 968.
- Gough, V. E. “Practical Tire Research.” Trans. SAE Vol. 64 (1956), p. 31.
- Van Eldik Thieme, H. C. A “Experimental and Theoretical Research on Mass-Spring Systems by the Vehicle Research Laboratory of the Technological University of Delft.” Proc. 8th International Automobile Technical Congress (FISITA) (1960), p. 374.
- J. R. Ellis contribution to Ref. 18, p. 414.
- Tritani (Toyoto Motor Co., Japan), “Forces on the Contact Patch of the Tyre,” Undated. MIRA Abstract (Oct. 12, 1960).
- Cooper, D. H. “Lateral Forces on Tyres,” Automobile Engineer (December, 1958); also, Kautschuk and Gummi, ibid, Vol. 11, No. 10 (1958), p. WT 273.
- Cooper, D. H. Gough, V. E. and Hardman, J. H. “Side-force and Slip in the Tyre Contact Patch.” Rev. Gen. du Caoutchouc, Vol. 36, No. 10 (October, 1959), p. 1331 (in English and French); also, in A. T. Z„ Vol. 63, p. 51 (in German).
- Gough, V. E. “Tyre and Vehicle Behaviour,” Automobile Engineer, Vol. 39 (March–April, 1949), p. 97, 139; also in Rev. Gen. du Caoutchouc, Vol. 28, No. 10 (October, 1951), p. 692.