This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
BEARINGS AND LUBRICANTS FOR AIRCRAFT TURBINE ENGINES
Annotation ability available
Sector:
Language:
English
Abstract
The paper describes the bearing and lubricant problems inherent in aircraft turbine engines; these problems are severe because of the occurrence of high rotative speeds and an extremely broad temperature range (including high temperatures as one end of the range). It is indicated that the materials currently used in rolling contact bearings for turbine engines are temperature limited to such an extent that completely new materials are now under consideration. Some data are presented which show acceptable friction and wear properties of some materials for rolling contact bearings and their cages (separators, retainers) at high speeds and at high temperatures. For liquid-lubricated-bearings, considerable improvement in the limiting speeds of rolling contact bearings appears possible with proper cage and bearing design. The design principle involves providing easy flow paths for the lubricant through the bearing.
The broad temperature range also imposes a temperature limitation problem on the lubricants. Synthetic lubricants have a considerably higher limiting temperature than the petroleums. For the higher temperatures, solid or gaseous lubricants are under consideration because of better thermal stability. Solids, such as MoS2 and graphite have been effective in lubrication of rolling contact bearings at high temperatures (500° to 1000° F). Similarly gases have been used as lubricants at high temperatures. Preliminary studies of the externally pressurized air bearing at 1000° F showed that a nonrotating bearing supported loads in a stable manner at this temperature.
The data and discussions of the paper show that there are bearing and lubricant materials which show promise for use at the high speeds and high temperatures of aircraft turbine engines. Considerable research is required, however, in laboratory apparatus, in full scale equipment under simulated conditions and in turbine engines.
Recommended Content
Technical Paper | PERFORMANCE OF TURBO ENGINE SYNTHETIC OILS |
Technical Paper | Temperature Limitations of Petroleum, Synthetic, and Other Lubricants in Rolling-Contact Bearings |
Technical Paper | A Look at the MIL-L-23699 (WEP) Lubricants |
Authors
Citation
JOHNSON, R. and BISSON, E., "BEARINGS AND LUBRICANTS FOR AIRCRAFT TURBINE ENGINES," SAE Technical Paper 550014, 1955, https://doi.org/10.4271/550014.Also In
References
- NACA Subcommittee on Lubrication and Wear: Review of Current and Anticipated Lubricant Problems in Turbojet Engines NACA RM E51D20 1951
- SAE Panel on High Speed Rolling Contact Bearings: Trends of Rolling Contact Bearings as Applied to Aircraft Gas Turbine Engines NACA TN 3110 1954 177 179
- Cross R. I. Synthetics Help Meet Stiff Lube Need of Turbo Engines SAE Journal 62 3 March 1954
- Johnson Robert L. Swikert Max A. Bisson Edmond E. Effective Lubrication Range for Steel Surfaces Boundary Lubricated at High Sliding Velocity by Various Classes of Synthetic Fluids NACA TN 2846 1952
- Christensen L. D. The Development of a Turbo-Prop Synthetic Lubricant Lubrication Engineering 8 4 Aug. 1952
- Hunt Kenneth C. Petroleum Requirements of British Gas Turbines. Part II - Lubricants SAE Journal 59 11 Nov. 1951 20 21
- Dawson J. G. Lubricating Problems of the Gas Turbine Engine Shell Aviation News 133 July 1949 14 22
- Bisson Edmond E. Johnson R. L. Turbojet Engine Lube Problem, Aided by Supplemental Lubes, Additives SAE Journal 58 3 Mar. 1950 39 41
- Synthetic Oils for Aircraft Gas Turbine Lubrication Lubrication 40 4 April 1954
- Bowden F. P. Tabor D. The Lubrication by Thin Metallic Films and the Action of Bearing Metals Jour. Appl. Phys. 14 3 Mar. 1943 141 151
- Johnson Robert L. Swikert Max A. Bisson Edmond E. Investigation of Wear and Friction Properties Under Sliding Conditions of Some Materials Suitable for Cages of Rolling Contact Bearings NACA Rep. 1062 1952
- Johnson Robert L. Swikert Max A. Bisson Edmond E. Wear and Sliding Friction Properties of Nickel Alloys Suited for Cages of High Temperature Rolling Contact Bearings. I - Alloys Retaining Mechanical Properties to 600° F NACA TN 2758 1953
- Johnson Robert L. Swikert Max A. Bisson Edmond E. Wear and Sliding Friction Properties of Nickel Alloys Suited for Cages of High Temperature Rolling Contact Bearings. II - Alloys Retaining Mechanical Properties above 600° F NACA TN 2759 1952
- Anderson William J. Macks E. Fred Nemeth Zolton N. Comparison of Operating Characteristics of Four Experimental and Two Conventional 75 mm Bore Cylindrical Bore Bearings at High Speeds NACA TN 3001 1953
- Murray S. F. Johnson R. L. Effects of Solvents in Improving Boundary Lubrication of Steel by Silicones NACA TN 2788 1952
- Murray S. F. Johnson R. L. Bisson Edmond E. Effect of High Bulk Temperature on Boundary Lubrication of Steel Surfaces by Synthetic Fluids NACA TN 2940 1953
- Nemeth Zolton N. Anderson W. J. Temperature Limitations of Petroleum, Synthetic, and other Lubricants in Rolling Contact Bearings SAE Fuels and Lubricants Meeting Tulsa, Oklahoma Nov. 4-5 1954
- Macks E. Fred Nemeth Z. N. Anderson W. J. Preliminary Investigation of Molybdenum Disulfide Air-Mist Lubrication for Roller Bearings Operating to DN Values of 1,000,000 and Ball Bearings Operating to Temperatures of 1000° F NACA RM E51G31 1951
- Pigott Joseph D. Marks E. Fred Air Bearing Studies at Normal and Elevated Temperatures Lubrication Engineering 10 1 Feb. 1954 29 33