This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Effects of Structure and System Parameters on Fuel Leakage Characteristics of Precision Coupling Components in Fuel Injector for Modern Diesel Engine
Technical Paper
2022-01-5028
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Event:
Automotive Technical Papers
Language:
English
Abstract
Increasing rail pressure is the development trend of high-pressure common rail system. When the rail pressure reaches ultrahigh range, fuel leakage of precision coupling components could have a significant impact on system performance. In order to investigate the effects of system and structure parameters on the leakage characteristics of precision coupling components, guide the design of ultrahigh-pressure common rail system, simulations were carried out. Variation of fuel leakage were studied with different structure and system parameters. A three-dimensional model of oil film with eccentric was developed to simulate eccentric between two parts of coupling component. The leakage in control valve component increases with common rail pressure; however, there is no obvious change in leakage of control piston component with rail pressure. Leakage flow rates in both components increased for about 27 times with the coupling component clearance widths increase from 2 μm to 6 μm, due to the increase in flow area and velocity. When the eccentric ratio varies from 0% to 50%, the leakage in both components within single cycle increased by about 37%-38%. Derivation of equation confirms the correctness of analysis on the influence of clearance width and eccentricity on fuel leakage.
Authors
Topic
Citation
Zhou, Y., Li, G., Li, H., Wu, X. et al., "Effects of Structure and System Parameters on Fuel Leakage Characteristics of Precision Coupling Components in Fuel Injector for Modern Diesel Engine," SAE Technical Paper 2022-01-5028, 2022, https://doi.org/10.4271/2022-01-5028.Also In
References
- Vassallo , A. , Beatrice , C. , Di Blasio , G. , Belgiorno , G. et al. The Key Role of Advanced, Flexible Fuel Injection Systems to Match the Future CO 2 Targets in an Ultra-Light Mid-Size Diesel Engine SAE Technical Paper 2018-37-0005 2018 https://doi.org/10.4271/2018-37-0005
- Di Blasio , G. , Beatrice , C. , Belgiorno , G. , Pesce , F. et al. Functional Requirements to Exceed the 100 kW/l Milestone for High Power Density Automotive Diesel Engines SAE Int. J. Engines 10 5 2017 2342 2353 https://doi.org/10.4271/2017-24-0072
- Agarwal , A.K. , Dhar , A. , Gupta , J.G. , Kim , W.I. et al. Effect of Fuel Injection Pressure and Injection Timing of Karanja Biodiesel Blends on Fuel Spray, Engine Performance, Emissions and Combustion Characteristics Energy Conversion and Management 91 2015 302 314
- Salvador , F.J. , Gimeno , J. , Carreres , M. , and Crialesi-Esposito , M. Fuel Temperature Influence on the Performance of a Last Generation Common-Rail Diesel Ballistic Injector. Part I: Experimental Mass Flow Rate Measurements and Discussion Energy Conversion and Management 114 2016 364 375
- Payri , R. , Salvador , F.J. , Carreres , M. , and De la Morena , J. Fuel Temperature Influence on the Performance of a Last Generation Common-Rail Diesel Ballistic Injector. Part II: 1D Model Development, Validation and Analysis Energy Conversion and Management 114 2016 376 391
- Payri , R. , Salvador , F.J. , Martí-Aldaraví , P. , and Martínez-López , J. Using One-Dimensional Modeling to Analyse the Influence of the Use of Biodiesels on the Dynamic Behavior of Solenoid-Operated Injectors in Common Rail Systems: Detailed Injection System Model Energy Conversion and Management 54 1 2012 90 99
- Salvador , F.J. , Gimeno , J. , De la Morena , J. , and Carreres , M. Using One-Dimensional Modeling to Analyze the Influence of the Use of Biodiesels on the Dynamic Behavior of Solenoid-Operated Injectors in Common Rail Systems: Results of the Simulations and Discussion Energy Conversion and Management 54 1 2012 122 132
- Salvador , F.J. , Martínez-López , J. , Caballer , M. , and De Alfonso , C. Study of the Influence of the Needle Lift on the Internal Flow and Cavitation Phenomenon in Diesel Injector Nozzles by CFD Using RANS Methods Energy Conversion and Management 66 2013 246 256
- Wang , C. , Li , G.-X. , Sun , Z.-Y. , Wang , L. et al. Effects of Structure Parameters on Flow and Cavitation Characteristics within Control Valve of Fuel Injector for Modern Diesel Engine Energy Conversion and Management 124 2016 104 115
- Sun , Z.-Y. , Li , G.-X. , Wang , L. , Wang , W.-H. et al. Effects of Structure Parameters on the Static Electromagnetic Characteristics of Solenoid Valve for an Electronic Unit Pump Energy Conversion and Management 113 2016 119 130
- Sun , Z.-Y. , Li , G.-X. , Yu-Song , Y. , Gao , S.-C. et al. Numerical Investigation on Transient Flow and Cavitation Characteristic within Nozzle during the Oil Drainage Process for a High-Pressure Common-Rail DI Diesel Engine Energy Conversion and Management 98 2015 507 517
- Ferrari , A. , Paolicelli , F. , and Pizzo , P. The New-Generation of Solenoid Injectors Equipped with Pressure-Balanced Pilot Valves for Energy Saving and Dynamic Response Improvement Applied Energy 151 367 376
- Yue , P. , Zhao , J. , Wei , K. , and Ma , X. The Fluid-Structure-Thermal Coupled Characteristics of the Leakage Rate of Piston Couples Interface for Common-Rail Injector Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science 233 16 5826 5835
- Lu , J. , Tang , S. , Zhou , Y. , Hong , J. et al. Simulation of Assembly Tolerance and Characteristics of High Pressure Common Rail Injector International Journal of Computational Intelligence Systems 4 6 1282 1289
- Dongiovanni , C. and Coppo , M. Accurate Modelling of an Injector for Common Rail Systems Siano , D. Fuel Injection Rijeka, Croatia InTech Open Access Publisher 2010 95 119
- LMS Imagine 2010
- Golubets , V.M. , Orel , V.M. , Pokhmurskii , V.I. , Mardarevich , R.S. et al. Influence of Chemical Nickel Coating on the Wear Resistance of Plunger Pairs of Coal-Mining High-Pressure Pumps Soviet Materials Science 16 1981 291 292
- ANSYS 2013