This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Evaluating the Mechanical Behavior of Fused Deposition Modeling Parameters of Raster Angle and Layer Thickness Effects on As-Built and Annealed Polymer Associated Composites
Technical Paper
2021-28-0283
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
Fused deposition Modeling (FDM) is one of the 3D techniques which are mainly used to fabricate the three-dimensional object directly and it is more economical method. The objective of this investigation is to primarily fabricate as-build and annealed polymer associated composites of carbon fiber Polyethylene Terephthalate Glycol (CF-PETG) material by FDM with the effect of different raster angle and layer thickness were consider as the prime parameters. The test specimen was prepared by FDM process with different raster angle (00/900, -450, +450, -450/+450) and layer thickness (100, 400 microns) with other parameters were kept constant. The study of the mechanical properties such as hardness, tensile and impact test of the as-built and annealed CF-PETG were investigated. The best results obtained for annealed specimens printed with raster angle of 00/900 and layer thickness of 100 microns produced more influence in all the mechanical properties. The high strength printed samples were suggested for conventional material replacement.
Authors
Topic
Citation
Ari Gowder Ravi Kumar, S., R, S., Dorai, A., Suresh Kumar, G. et al., "Evaluating the Mechanical Behavior of Fused Deposition Modeling Parameters of Raster Angle and Layer Thickness Effects on As-Built and Annealed Polymer Associated Composites," SAE Technical Paper 2021-28-0283, 2021, https://doi.org/10.4271/2021-28-0283.Also In
References
- Gibson , I. , Rosen , D. , and Stucker , B. Additive Manufacturing Technologies 2015 https://doi.org/10.1007/978-1-4939-2113-3
- Ngo , T.D. , Kashani , A. , Imbalzano , G. , Nguyen , K.T.Q. et al. Additive Manufacturing (3D printing) : A Review of Materials, Methods, Applications and Challenges Composite Part B: Engineering 143 2018 172 196 https://doi.org/10.1016/j.compositesb.2018.02.012
- Guo , J. , Xiao , R. , and Tian , C. Optimizing Physical Aging in Poly Ethylene Terephthalate Glycol (PETG) Journal of Non-Crystalline Solids 502 2018 15 21 https://doi.org/10.1016/j.jnoncrysol.2018.10.021
- Srinivasan , R. , Prathap , P. , Raj , A. , Kannan , S.A. et al. Influence of Fused Deposition Modeling Process Parameter on the Mechanical Properties of PETG Parts Materials Today: Proceedings 27 2-4 2020 https://doi.org/10.1016/j.matpr.2020.03.809
- Luzanin , O. , Movrin , D. , and Plancak , M. Effect of Layer Thickness, Deposition Angle, and Infill on Maximum Flexural Force in FDM-Built Specimens Journal for Technology of Plasticity 39 2014
- Ranganathan , S. , Kumar , K.S. , gopal , S. , and Palanivelu , R. Enhancing the Tribological Properties PETG and CFPETG Composites Fabricated by FDM via Various Infill Density and Annealing SAE Technical Paper 2020-28-0429 2020 https://doi.org/10.4271/2020-28-0429
- Srinidhi , M.S. , Soundararajan , R. , Suresh , S. , and Devanand , A. https://doi.org/10.1016/j.matpr.2021.02.417
- Sathish Kumar , K. , Soundararajan , R. , Shanthosh , G. , Saravanakumar , P. et al. Augmenting Effect of Infill Density and Annealing on Mechanical Properties of PETG and CFPETG Composites Fabricated by FDM Materials Today: Proceedings 2020 https://doi.org/10.1016/j.matpr.2020.10.078
- Szykiendans , K. , Credo , W. , and Osinski , D. Selected Mechanical Properties of PETG 3D prints Procedia Eng 177 2017 455 461 https://doi.org/10..1016/j.proeng.2017.02.245
- Li , N. , Li , Y. , and Liu , S. Rapid Prototyping of Continuous Carbon Fiber Reinforced Polylactic Acid Composites by 3D Printing J. Mater. Process. Technol. 238 2016 218 225 https://doi.org/10.1016/j.jmatprotec.2016.07.025
- Jiang , D. and Smith , D.E. Anistropic Mechanical Properties of Oriented Carbon Fiber Filled Polymer Composites Produced with Fused Filament Fabrication Addit. Manuf. 18 2017 84 89 https://doi.org/10.1016/j.addma.017.08.006
- Dolzyk , G. and Jung , S. Tensile and Fatigue Analysis of 3d- Printed Polyethylene Terephthalate Glycol J. Fail. Anal Preven. 19 2 2019 511 518 https://doi.org/10.1007/s11668-019-00631-z
- Dev Singh , D. , Raji Reddy , A. , Arjulant , S. , and Res , J. Characterization of Additive Manufactured PETG and Carbon Fiber -PETG International Journal for Research in Engineering Application & Management 04 02 2018 152 156 10.18231/2454-9150.2018.0139
- Maurya , N. , Rastogi , V. , and Sigh , P. Fabrication of Prototype Connecting Rod of PLA Plastic Material Using FDM Prototype Technology Indian Journal of Engineering & Materials Sciences 07 2020 333 343
- Shubham , P. , Sikidar , A. , and Chand , T. Key The Influence of Layer Thickness on Mechanical Properties of the 3D Printed ABS Polymer by Fused Deposition Modeling Key Engineering Materials 706 2016 63 67