This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Experimental and Modeling Study of Spark Plug Electrode Heat Transfer and Thermal Energy Deposition
Technical Paper
2021-01-0480
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Event:
SAE WCX Digital Summit
Language:
English
Abstract
Spark plug electrode heat transfer and its relationship with the thermal energy deposition from the spark plasma to the gas in the spark gap was studied under quiescent non-combusting conditions. The thermal energy deposition to the gas (N2) was measured with a spark plug calorimeter as a function of pressure, up to 30 bar. The measurements were carried out for two gap distances of 0.3 mm and 0.9 mm, for three nominally identical spark plugs having different electrode surface area and/or surface thermal conductivity. The unmodified baseline spark plug had a nickel center electrode (cathode) 2.0 mm in diameter, the first modified spark plug had both the ground and center electrodes shaved to a diameter of approximately 0.5 mm, and the second modified spark plug had copper inserts bonded to both electrodes. The experimental results were compared with multi-dimensional simulations of the conjugate heat transfer to the gas and to the metal electrodes, conducted using CONVERGE CFD. Consistent with the literature, the measurements showed the thermal energy deposition to the gas increased with both increasing pressure and spark gap distance. The thermal energy deposition to the gas was found similar for both the unmodified and the shaved fine-wire electrode plugs, however the delivered electrical energy to the gap was approximately one third less for the fine-wire electrode plug, resulting a higher energy conversion efficiency for the fine-wire plug. The simulations indicated that the temperature rise of the metal electrode surfaces was mostly confined to the immediate area of contact with the plasma arc and that heat loss to other parts of the spark plug and to the calorimeter walls was negligible over the time-scale of the arc duration. For a steel electrode with an assumed arc diameter of 0.1 mm, the maximum predicted rise in surface temperature was approximately 175 oC. The simulations indicated that the high thermal conductivity of a copper surface resulted in locally lower temperature peaks and, as expected, more rapid diffusion of the heat affected zone such that the 1/e time for the temperature dissipation was approximately 0.6 ms after the end of the spark. Experimentally, the high thermal conductivity copper surfaces had no measureable effect on the thermal energy deposition. The results showed that spark plug electrode surface area had only a small effect on the thermal energy deposition to the gas and little effect on the amount of heat transfer from the arc to the electrodes under the investigated conditions where the gap fluid motion was small. An implication may be that if spark plug electrode size and geometry affects flame initiation, it is due to heat loss from the nascent flame kernel rather than from the spark plasma.
Recommended Content
Authors
Topic
Citation
Kim, K., Tambasco, C., Hall, M., and Matthews, R., "Experimental and Modeling Study of Spark Plug Electrode Heat Transfer and Thermal Energy Deposition," SAE Technical Paper 2021-01-0480, 2021, https://doi.org/10.4271/2021-01-0480.Also In
References
- Kono , M. , Kumagai , S. , and Sakai , T. The Optimum Condition for Ignition of Gases by Composite Sparks Symposium (International) on Combustion 16 1 757 766 January 1977
- Ko , Y. , and Anderson , R. Electrode Heat Transfer During Spark Ignition SAE Technical Paper 892083 1989 https://doi.org/10.4271/892083
- Osamura , H. , and Abe , N. Development of New Iridium Alloy for Spark Plug Electrodes SAE Technical Paper 1999-01-0796 1999 https://doi.org/10.4271/1999-01-0796
- Hori , T. , Shibata , M. , Okabe , S. , and Hashizume , K. Super Ignition Spark Plug with Fine Center & Ground Electrodes SAE Technical Paper 2003-01-0404 2003 https://doi.org/10.4271/2003-01-0404
- Alger , T. , Mangold , B. , Mehta , D. , and Roberts , C. The Effect of Sparkplug Design on Initial Flame Kernel Development and Sparkplug Performance SAE Technical Paper 2006-01-0224 2006 https://doi.org/10.4271/2006-01-0224
- Abidin , Z. , and Chadwell , C. Parametric Study and Secondary Circuit Model Calibration Using Spark Calorimeter Testing SAE Technical Paper 2015-01-0778 2015 https://doi.org/10.4271/2015-01-0778
- Roth , W. , Guest , P.G. , Elbe , G. , and Lewis , B. Heat Generation by Electric Sparks and Rate of Heat Loss to the Spark Electrodes Journal of Chemical Physics 19 12 1530 1535 1951
- Merritt , L.R. A Spark Calorimeter Journal of Physics E: Scientific Instruments 11 193 194 1978
- Franke , A. , and Reinmann , R. Calorimetric Characterization of Commercial Ignition Systems SAE Technical Paper 2000-01-0548 2000 https://doi.org/10.4271/2000-01-0548
- Teets , R.E. , and Sell , J.A. Calorimetry of Ignition Sparks SAE Technical Paper 880204 1988 https://doi.org/10.4271/880204
- Kim , K. , Hall , M.J. , Wilson , P.S. , and Matthews , R.D. Arc-Phase Spark Plug Energy Deposition Characteristics Measured Using a Spark Plug Calorimeter Based on Differential Pressure Measurement Energies 13 3550 2020 10.3390/en13143550
- Meek , N.F. Electrical Breakdown of Gases London, UK Oxford at the Clarendon Press 1953