This content is not included in your SAE MOBILUS subscription, or you are not logged in.
3rd Generation AHSS Virtual and Physical Stamping Evaluation
ISSN: 0148-7191, e-ISSN: 2688-3627
Published April 14, 2020 by SAE International in United States
This content contains downloadable datasetsAnnotation ability available
Developing lightweight, stiff and crash-resistant vehicle body structures requires a balance between part geometry and material properties. High strength materials suitable for crash resistance impose geometry limitations on depth of draw, radii and wall angles that reduce geometric efficiency. The introduction of 3rd generation Advanced High Strength Steels (AHSS) can potentially change the relationship between strength and geometry and enable simultaneous improvements in both. This paper will demonstrate applicability of 3rd generation AHSS with higher strength and ductility to replace the 780 MPa Dual Phase steel in a sill reinforcement on the current Jeep Cherokee. The focus will be on formability, beginning with virtual simulation and continuing through a demonstration run on the current production stamping tools and press.
CitationMacek, B. and Lutz, J., "3rd Generation AHSS Virtual and Physical Stamping Evaluation," SAE Technical Paper 2020-01-0757, 2020, https://doi.org/10.4271/2020-01-0757.
Data Sets - Support Documents
|[Unnamed Dataset 1]|
- Hance, B. , “Advanced High-Strength Steel (AHSS) Performance Level Definitions and Targets,” SAE Int. J. Mater. Manf 11(4):505-516, 2018, https://doi.org/10.4271/2018-01-0629.
- McKune, P., Khutorsky, A., and Butala, K. , “Replacing Press Hardenable Steel with 980 MPa Generation 3 Steel for Automotive Pillars,” SAE Technical Paper 2018-01-0117, 2018, https://doi.org/10.4271/2018-01-0117.
- Huang, L. and Shi, M. , “Forming Limit Curves of Advanced High Strength Steels: Experimental Determination and Empirical Prediction,” SAE Int. J. Mater. Manf 11(4):409-418, 2018, https://doi.org/10.4271/2018-01-0804.
- Pai, J. , “Evaluation of FMVSS No. 301, Fuel System Integrity, as Upgraded in 2005 to 2009,” Report No. DOT HS 812 038, National Highway Traffic Safety Administration, Washington, DC, June 2014.
- “LS-DYNA Keyword User’s Manual Volume II Material Models,” Version 04/06/16 (r: 7556), Livermore Software Technology Company, Livermore, CA, April 2016.
- World Auto Steel (Version 6.0), “Advanced High-Strength Steels Application Guidelines,”April 2017.
- Link, T. and Hance, B. , “Axial and Bending Crash Performance of Advanced High-Strength Steels,” AISI, 2017.
- Chen, X., Chen, G., and Huang, L. , “Validation of GISSMO Model for Fracture Prediction of a Third-Generation Advanced High-Strength Steel,” SAE Int. J. Mater. Manf 11(4):293-302, 2018, https://doi.org/10.4271/2018-01-0107.
- ASTM International , “Standard Test Methods for Tension Testing of Metallic Materials,” Standard Designation E8/E8M -15a, 2015.
- Shih, H., Shi, M., Zeng, D., and Xia, Z. , “Development of Empirical Shear Fracture Criterion for AHSS,” SAE Int. J. Mater. Manuf 3(1):670-675, 2010, https://doi.org 10.4271/2010-01-0977.
- Tyson, J., Coe, D., Schmidt, T., and Galanulis, K. , “Next Generation 3D Optical Measurements for Manufacturing,” SAE Technical Paper 2005-01-0490, 2005, https://doi.org/10.4271/2005-01-0490.