This content is not included in your SAE MOBILUS subscription, or you are not logged in.
Influence of Intake Valve Lift on Flow Capacity of Intake Port
ISSN: 0148-7191, e-ISSN: 2688-3627
Published April 02, 2019 by SAE International in United States
This content contains downloadable datasetsAnnotation ability available
A three-dimensional model of a diesel engine intake port was established and was verified by steady-flow test. Based on this model, the influence of intake valve lift on the flow capacity of intake port was studied and a design method of maximum valve lift was put forward. The results show that, under different intake pressure and relative pressure difference conditions, the discharge coefficient increases first and then converges with the increase of valve lift. Under the same valve lift condition, with the increase of relative pressure difference, the discharge coefficient decreases slightly in subsonic state and decreases sharply from subsonic state to supersonic state, but the mass flow rate increases slightly. The optimum ratio of valve lift and valve seat diameter is related to relative pressure difference, it increases first and then keeps constant with the increase of relative pressure difference. When the optimum maximum valve lift is design, The optimum maximum valve lift at the working condition of maximum relative pressure difference can be used as the optimum value in the whole working conditions.
|Technical Paper||Modelling of Gasoline and Ethanol Hollow-Cone Sprays Using OpenFOAM|
|Aerospace Standard||Valve, Air, High Pressure Charging, 5000 psi|
|Ground Vehicle Standard||Hydraulic Directional Control Valves, 3000 psi Maximum|
CitationXu, Y., Liu, F., Rui, J., Hua, Y. et al., "Influence of Intake Valve Lift on Flow Capacity of Intake Port," SAE Technical Paper 2019-01-0223, 2019, https://doi.org/10.4271/2019-01-0223.
Data Sets - Support Documents
|[Unnamed Dataset 1]|
|[Unnamed Dataset 2]|
- Wei, Z., “Simulation and Experimental Study on Performance Optimization of High Speed Gasoline Engine,” Tianjin University, Tianjin, 2013.
- Nassiri-Toosi, A., Raei-Tabar, and Ghamari, M., “Numerical Simulation of Intake Port Flow by Using VECTIS CFD Code,” SAE Technical Paper 2003-32-0072, 2003, doi:10.4271/2003-32-0072.
- Rao, G.U., Murali, S., Marathe, N. et al., “Parametric Study of Flow through Engine Exhaust Port Using CFD,” International Journal of Heat and Technology 45(12):478-485, 2008.
- Semlitsch, B., Wang, Y., and Mihăescu, M., “Flow Effects due to Valve and Piston Motion in an Internal Combustion Engine Exhaust Port,” Energy Conversion and Management 45(96):18-30, 2015.
- Wang, Y., Semlitsch, B., and Madhavan, T., “Flow Induced Energy Losses in the Exhaust Port of an Internal Combustion Engine,” Journal of Fluids Engineering 137(1):109-121, 2014.
- Peng, X., “Numerical Simulation and Optimization Design of Engine Intake Port,” North University of China, Taiyuan, Shanxi, 2014.
- Chunhui, W., Jilin, L., Dewen, J. et al., “A Research on the Intake Flow and In-Cylinder Flow Field in a Four-valve DI Diesel Engine,” Automotive Engineering 36(1):38-42, 92, 2014.
- Bin, Z., “CFD Study on Intake Port of Vehicle Diesel Engine,” Xihua University, Chengdu, Sichuan, 2010.
- Zunqing, Z., Wenqiang, Z., Mingfa, Y. et al., “Effect of High/Low Pressure EGR on Combustion and Emissions of Two-Stage Turbocharged Diesel Engine,” Chinese Internal Combustion Engine Engineering 35(01):1-7, 2014.
- Bo, L., Zhilong, H., Hualei, L. et al., “Experiment on Characteristic of Bypass Valves and Regulating MAP of a Regulated Two-Stage Turbocharged Diesel Engine,” Transactions of CSICE 30(01):72-78, 2012.
- Parlak, A., Yasar, H., Soyhan, H.S. et al., “Optimization of an Irreversible Diesel Cycle: Experimental Results of a Ceramic Coated Indirect-Injection Supercharged Diesel Engine,” Energy & Fuels 22(3):1930-1935, 2008.
- Jayashankara, B. and Ganesan, V., “Effect of Fuel Injection Timing and Intake Pressure on the Performance of a DI Diesel Engine - A Parametric Study Using CFD,” Energy Conversion and Management 51(10):1835-1848, 2010.
- Ruilin, L., Zhigang, L., Wuquan, L. et al., “Studies on Steady Measurements of In-Cylinder Tumble in a 4-Valve Engine with One Inlet Valve Opening,” Transactions of CSICE 19(05):405-409, 2001.
- Ruilin, L., Lizhe, G., Zhigang, L. et al., “Studies on Steady Measurements of In-Cylinder Swirl in a 4-Valve Gasoline Engine,” Transactions of CSICE 19(04):377-382, 2001.
- Tianyou, W., Rongwen, L., Shuliang, L. et al., “Study on Steady Flow Test Method for Inlet Port of DI Diesel Engines with Variable Pressure Drop,” Transactions of CSICE 23(2):131-136, 2005.
- Fushui, L., Ning, K., Xuyang et al., “Discharge Coefficient Evaluation and Steady Flow Characteristics for Intake Port of Turbocharged Diesel Engine,” 48(06):341-348, 2017.
- Baohua, Z., Fluid Mechanics (China: Peking University Press, 2013), 68.
- Zhengtan, X., Fluid Mechanics (China: Chemical Industry Press, 2009), 73.
- Baolong, Z., Internal Combustion Engine (China: Machinery Industry Press, 2011).
- Liwei, S., Xiong, S., Junfeng, X. et al., “Numerical and Experimental Study on Gas Intake Process in Diesel with High Pressure Drop,” Acta Armamentarii 32(11):1310-1314, 2011.