This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Lap Time Simulation Tool for the Development of an Electric Formula Student Car
Technical Paper
2019-01-0163
ISSN: 0148-7191, e-ISSN: 2688-3627
This content contains downloadable datasets
Annotation ability available
Sector:
Language:
English
Abstract
This work details the development of a lap time simulation (LTS) tool for use by Queen’s University Belfast in the Formula Student UK competition. The tool provides an adaptable, user-friendly virtual test environment for the development of the team’s first electric vehicle. A vehicle model was created within Simulink, and a series of events simulated to generate the performance envelope of the car in the form of maximum combined lateral/longitudinal accelerations against velocity (ggv diagram). A four-wheeled vehicle including load transfer was modelled, capturing shifts in traction between each tire, which can influence performance in vehicles where the total tractive power is split between individual wheel motors. The acceleration limits in the ggv diagram were used to simulate the acceleration and endurance events at Formula Student. These events were simulated using a MATLAB code considering a point mass, quasi-steady state model with a perfect driver. This method considering all four wheels captures performance characteristics that point mass models normally cannot, without the complexity and time required for more detailed LTS solutions including yaw movements and driver models. It also separates the vehicle model from the MATLAB code required to run the LTS, reducing the complexity of implementing future changes. The LTS was benchmarked against the freeware tool OptimumLap and validated where possible against competition results. A Latin Hypercube sampling technique was employed to generate numerous input scenarios for the simulation, and a response surface fitted to the results to perform a sensitivity analysis. Results from this analysis indicate several areas to efficiently focus future resource allocation as well as attempting to quantify trade-offs. Optimum powertrain gear ratio and battery capacity for a proposed vehicle were specified using the tool.
Recommended Content
Authors
Topic
Citation
Doyle, D., Cunningham, G., White, G., and Early, J., "Lap Time Simulation Tool for the Development of an Electric Formula Student Car," SAE Technical Paper 2019-01-0163, 2019, https://doi.org/10.4271/2019-01-0163.Data Sets - Support Documents
Title | Description | Download |
---|---|---|
Unnamed Dataset 1 | ||
Unnamed Dataset 2 | ||
Unnamed Dataset 3 | ||
Unnamed Dataset 4 |
Also In
References
- Formula SAE Online https://www.fsaeonline.com 2018
- Srinivasan , P. and Kothalikar , M. Performance Fuel Economy and CO2 Prediction of a Vehicle using AVL Cruise Simulation Techniques SAE Technical Paper 2009-01-1862 2009 10.4271/2009-01-1862
- Govender , V. and Barton , D. Multibody System Simulation and Optimisation of the Driving Dynamics of a Formula SAE Race Car SAE Technical Paper 2009-01-0454 2009 10.4271/2009-01-0454
- Costa , R. and Bortolussi , R. Lap Time Simulation of Formula SAE Vehicle with Quasi-Steady State Model SAE Technical Paper 2016-36-0164 2016 10.4271/2016-36-0164
- 2012
- Sakhalkar , S. , Dhillon , P. , Bakshi , S. , Kumar , P. et al. Powertrain Model for Selection of Reduction Ratio and Estimation of Energy Requirement SAE Technical Paper 2014-01-1781 2014 10.4271/2014-01-1781
- Formula Student Rules 2018 https://www.imeche.org/events/formula-student/team-information/rules 2018
- Stevens , G. , Murtagh , M. , Kee , R. , Early , J. et al. Development of a Vehicle Model Architecture to Improve Modeling Flexibility SAE Int. J. Engines 10 3 1328 1366 2017 10.4271/2017-01-1138
- Criens , C. , Damten , T. , Luijten , H. , and Rutjes , T. 2006
- DUT 12 https://www.fsteamdelft.nl/dut12 2019
- White , G. , Cunningham , G. , and Doyle , D. Design of an Electric Drive Transmission for a Formula Student Race Car SAE Technical Paper 2019-01-1295 2019
- August Aune , P. 2016
- Wang , G.G. Adaptive Response Surface Method Using Inherited Latin Hypercube Design Points J. Mech. Des 125 2 210 220 2003 10.1115/1.1561044