This content is not included in your SAE MOBILUS subscription, or you are not logged in.
Spectral/hp iLES-SVV simulation methodology study on an Ahmed Body squared back
ISSN: 0148-7191, e-ISSN: 2688-3627
Published September 03, 2018 by SAE International in United States
This content contains downloadable datasetsAnnotation ability available
The Ahmed Body is one of the most widely studied bluff bodies used for automotive conceptual studies and Computational Fluid Dynamics - CFD software validation. With the advances of the computational processing capacity and improvement in cluster costs, high-fidelity turbulence models, such as Detached Eddies Simulation – DES and Large Eddies Simulation – LES, are becoming a reality for industrial cases, as studied by BUSCARIOLO et al. (2016) , evaluating DES models to automotive applications.
This work presents a correlation study between a computational and physical model of an Ahmed Body with slant angle of 0 degree, also known as a squared back. Physical results are from a wind tunnel test, performed by STRACHAN et al. (2007)  considering moving ground and Reynolds number of 1.7M, based on the length of the body.
CFD simulations were performed by the code Nektar++, which is an open source spectral/hp element high-order solver, which methodology combine both mesh refinement (h), with higher polynomial order (p) for lower error propagation and better convergence. It employs a high-fidelity turbulence model known as Spectral Vanish Viscosity – iLES-SVV model, which works as a filter for high frequencies. Same physical test conditions and tunnel test section were considered, with a total time of 4 convective lengths.
The 4 cases studies consider high-order mesh of 6th order, divided in two polynomial orders: 5th and 6th for two different mesh setups: one base mesh setup with around 95,000 elements corresponding to 6.3Million of DOFs and a second mesh considering a refinement (h) with around 310,000 elements, corresponding to 19.8 Million of DOFs. Meshes were generated by NekMesh, which works with Nektar++ for high-order mesh generation. In order to improve the computational costs, only half of the model is simulated, considering symmetric condition.
Considering the converged drag coefficient values for cases of 5th and 6th polynomial order and refined mesh, the maximum difference found, compared with experimental results with moving ground configuration, there is a maximum difference of 5%. For the lift coefficient the maximum difference between the simulation results compared to experimental data is 25%, but the closest result is fully correlated. There is also a good agreement between the LDA measurements on the end of the body with the results from the simulation. The methodology shows promising results against the open literature once an appropriate validation study has been undertaken. Despite the relatively course resolution adopted the results are encouraging. Having identified an appropriate resolution, we will next consider other slant angles, to see how well these correlate with the experimental studies.
CitationBuscariolo, F., Sherwin, S., Assi, G., and Meneghini, J., "Spectral/hp iLES-SVV simulation methodology study on an Ahmed Body squared back," SAE Technical Paper 2018-36-0320, 2018, https://doi.org/10.4271/2018-36-0320.
Data Sets - Support Documents
- Huminic, A. and Huminic, G.. “Computational study of flow in the underbody diffuser for a simplified car model”. Technical report, SAE Technical Paper, 2010.
- Cantwell, C.D., Moxey, D., Comerford, A., Bolis, A., Rocco, G., Mengaldo, G., De Grazia, D., Yakovlev, S., Lombard, J-E., Ekelschot, D., et al. “Nektar++: An open-source spectral/hp element framework”. Computer Physics Communications, 192:205–219, 2015.
- Serre, E., Minguez, M., Pasquetti, R., Guilmineau, E., Deng, G.B., Kornhaas, M., Schäfer, M., Fröhlich, J., Hinterberger, C., and Rodi. W., “On simulating the turbulent flow around the ahmed body: A french–german collaborative evaluation of les and des”. Computers & Fluids, 78:10–23, 2013.
- Buscariolo, F.F., Magazoni, F., Wolf, M., Maruyama, F., Alves, J.C.L., Volpe, L.D., “Analysis of Turbulence Models Applied to CFD Drag Simulations of a Small Hatchback Vehicle”, SAE Paper, N° 2016-36-0201, Society of Automotive Engineers, 2016.
- Karniadakis, G.E., Sherwin, S.J., “Spectral/hp Element Methods for Computational Fluid Dynamics”, Oxford Science Publications, 2013.
- Lienhart, H., and Becker, S., “Flow and turbulence structure in the wake of a simplified car model”. Technical report, SAE Technical Paper, 2003.
- Xu, H., Cantwell, C.D., Monteserin, C., Eskilsson, C., Engsig-Karup, A.P., Sherwin, S.J., “Spectral/hp element methods: Recent developments, applications, and perspectives”. Journal of Hydrodynamics, 2018.
- Nektar ++ - www.nektar.info
- Sagaut, P. “Large eddy simulation for incompressible flows” [M]. Berlin, Heidelberg, Germany: Springer-Verlag, 2001.
- Adams, R.A. “Sobolev spaces”[M]. New York, USA: Academic Press, 1975.
- Strachan, R.K., Knowles, K., and Lawson, N.J., “The vortex structure behind an Ahmed reference model in the presence of a moving ground plane”. Experiments in fluids, 42(5):659–669, 2007.
- Ahmed, S.R., Ramm, G., and Faltin, G., “Some salient features of the time-averaged ground vehicle wake”. Technical report, SAE Technical Paper, 1984.
- Morel, T. “Aerodynamic drag of bluff body shapes characteristic of hatch-back cars”. Technical report, SAE Technical Paper, 1978.