This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
A Study on Hypoid Gears NVH Robustness
Journal Article
2017-01-1776
ISSN: 2380-2162, e-ISSN: 2380-2170
Sector:
Citation:
Kolivand, M., Steyer, G., Krieger, C., and Stroh, M., "A Study on Hypoid Gears NVH Robustness," SAE Int. J. Veh. Dyn., Stab., and NVH 1(2):417-427, 2017, https://doi.org/10.4271/2017-01-1776.
Language:
English
References
- Sun , Z. , Steyer , G. , Meinhardt , G. , and Ranek , M. NVH Robustness Design of Axle Systems SAE Technical Paper 2003-01-1492 2003 10.4271/2003-01-1492
- Donley , M. , Lim , T. , and Steyer , G. Dynamic Analysis of Automotive Gearing Systems SAE Technical Paper 920762 1992 10.4271/920762
- Steyer , G. C. , and Lim , T. C. 1991 System Dynamics in Quiet Gear Design Proceedings of the 9th International Modal Analysis Conference 999 1005
- Chung , C. , Steyer , G. , Abe , T. , Clapper , M. et al. Gear Noise Reduction through Transmission Error Control and Gear Blank Dynamic Tuning SAE Technical Paper 1999-01-1766 1999 10.4271/1999-01-1766
- Hirasaka , N. , Sugita , H. , and Asai , M. A Simulation Method of Rear Axle Gear Noise SAE Technical Paper 911041 1991 10.4271/911041
- Park , D. , Kolivand , M. , and Kahraman , A. 2014 An Approximate Method to Predict Surface Wear of Hypoid Gears Using Surface Interpolation Mech. Mach. Theory 71 64 78
- Park , D. , Kolivand , M. , and Kahraman , A. Prediction of Surface Wear of Hypoid Gears Using a Semi-Analytical Contact Model Mech. Mach. Theory 52 180 194
- Kolivand , M. , and Kahraman , A. 2009 A Load Distribution Model for Hypoid Gears Using Ease-off Topography and Shell Theory Mech. Mach. Theory 44 10 1848 1865
- Kolivand , M. , and Kahraman , A. 2010 An Ease-Off Based Method for Loaded Tooth Contact Analysis of Hypoid Gears Having Local and Global Surface Deviations J. Mech. Des. 132 7 071004 071004
- Litvin , F. L. , and Fuentes , A. 2004 Gear Geometry and Applied Theory Cambridge University Press
- Vecchiato , D. 2005 Design and Simulation of Face-Hobbed Hypoid Gears, and Tooth Contact Analysis by Boundary Element Method University of Illinois at Chicago
- Stadtfeld , H. J. 1993 Handbook of Bevel and Hypoid Gears: Calculation, Manufacturing, Optimization
- Simon , V. Tooth Contact Analysis of Mismatched D Hypoid Gears Int. Power Transmission and Gearing Conference San Diego
- Simon , V. 1998 Load Distribution in Hypoid Gears J. Mech. Des. 122 4 529 535
- Gosselin , C. , Cloutier , L. , and Brousseau , J. 1991 Tooth Contact Analysis of High Conformity Spiral Bevel Gears Proceedings of JSME Int. Conf. on Motion and Power Transmission Hiroshima, Japan 725 730
- Kolivand , M. , and Kahraman , A. 2011 A General Approach to Locate Instantaneous Contact Lines of Gears Using Surface of Roll Angle J. Mech. Des. 133 1 014503 014503
- Artoni , A. , Gabiccini , M. , and Kolivand , M. 2013 Ease-off Based Compensation of Tooth Surface Deviations for Spiral Bevel and Hypoid Gears: Only the Pinion Needs Corrections Mech. Mach. Theory 61 84 101
- Artoni , A. , Gabiccini , M. , Guiggiani , M. , and Kahraman , A. 2011 Multi-Objective Ease-Off Optimization of Hypoid Gears for Their Efficiency, Noise, and Durability Performances J. Mech. Des. 133 12 121007 121007
- Conry , T. F. , and Seireg , A. 1973 A Mathematical Programming Technique for the Evaluation of Load Distribution and Optimal Modifications for Gear Systems J. Manuf. Sci. Eng. 95 4 1115 1122
- Vaidyanthan , S. , Houser , D. , and Busby , H. 1993 A Rayleigh-Ritz Approach to Determine Compliance and Root Stresses in Spiral Bevel Gears Using Shell Theory AGMA 93FTM03
- Stegmiller , M. E. , and Houser , D. R. 1993 A Three Dimensional Analysis of the Base Flexibility of Gear Teeth J. Mech. Des. 115 1 186 192
- Weber , C. 1951 The Deformation of Loaded Gears and the Effect on Their Load Carrying Capacity (PartI), II Department of Scientific and Industrial Research
- Kolivand , M. , Hannaneh , A. , Soltani , N. , and Shoroki , Z. K. 2006 Retaining Hypoid Gear Performance Characteristics With Differential Housing and Shafts Deflections 47675 361 369
- Kolivand , M. , Soltani , N. , Hannaneh , A. , and Shoroki , Z. K. 2006 Optimization of Hypoid Gears Performance Characteristics With Typical Manufacturing and Assembly Errors 42495 15 23
- Makam , S. 2010 An Experimental Study on the Influence of Misalignments on the Static Transmission Error of Hypoid Gear Pairs The Ohio State University
Cited By
Recommended Content
Journal Article | Statistical Characterization, Pattern Identification, and Analysis of Big Data |
Journal Article | Nonlinear Time-Varying Dynamic Interactions of Hypoid Gear-Shaft-Bearing Systems |
Technical Paper | Tolerancing Large Diameter Bearings |