This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Influence of an Automatic Transmission with a Model Predictive Control and an On-Demand Clutch Actuator on Vehicle Fuel Consumption
Technical Paper
2016-01-1115
ISSN: 0148-7191, e-ISSN: 2688-3627
This content contains downloadable datasets
Annotation ability available
Sector:
Language:
English
Abstract
The demand for lower CO2 emissions requires not just the optimization of every single component but the complete system. For a transmission system, it is important to optimize the transmission hardware as we well as the interaction of powertrain components. For automatic transmission with wide ratio spreads, the main losses are caused by the actuation system, which can be reduced with use of ondemand actuation systems. In this paper, a new on-demand electromechanical actuation system with validation results on a clutch test bench is presented. The electro-mechanical actuator shows an increase in the efficiency of 4.1 % compared to the conventional hydraulic actuation in a simulated NEDC (New European Driving Cycle) cycle. This increase is based on the powerless end positions of the actuator (engaged and disengaged clutch). The thermal tension and wear are compensated with a disk spring. This allows a stable control over service life. This actuation system is developed for a new 7-speed automatic transmission layout and with a model predictive controller the fuel economy and comfort issues are optimized. The decrease in fuel consumption is achieved with an optimized shift strategy depending on the driver type determination. This enables 13 % lower fuel consumption for a small gasoline passenger car (vehicle mass: 1250 kg, air drag coefficient: 0.3, roll resident coefficient: 0.01, total powertrain efficiency NEDC: 20 %) in the NEDC simulation compared to manual shifting defined by legislation. The combination of an on-demand electro-mechanical actuator and a model predictive transmission controller is shown to achieve a fuel consumption reduction of 17.1 % for a small gasoline passenger car.
Recommended Content
Topic
Citation
Huth, T. and Pischinger, S., "Influence of an Automatic Transmission with a Model Predictive Control and an On-Demand Clutch Actuator on Vehicle Fuel Consumption," SAE Technical Paper 2016-01-1115, 2016, https://doi.org/10.4271/2016-01-1115.Data Sets - Support Documents
Title | Description | Download |
---|---|---|
Unnamed Dataset 1 |
Also In
References
- Hamm , T , Hellenbroich , G. , Huth , T. New planetary based hybrid automatic transmission with true on-demand actuation CTI “Automotive Transmissions and Hybrid & Electric Drives North America Auburn Hills, Michigan, USA May 16 - 19, 2011
- Karch , G. , Grumbach , M. , Mohr , M. Potenziale und Grenzen der Verbrauchsreduktion durch Maßnahmen in Antrieb und Fahrwerk VDI-Berichte Nr. 1957, VDI Verlag Düsseldorf 2006
- Naunheimer , H. , Bertsche , B. , Lechner , G. Fahrzeuggetriebe - Grundlagen, Auswahl, Auslegung und Konstruktion Springer Verlag Heidelberg 2007
- Bednarek , G. , Kahraman , A. , Seetharaman , S. Entwicklung eines Wirkungsgradmodells für Schaltgetriebe VDI-Bericht Nr. 2029, VDI Verlag Düsseldorf 2008
- Schneider , E. et al. Optimale Getriebe als Ergebnis einer ganzheitlichen Antriebsstrang-Auslegung 30. Internationales Wiener Motorensymposium 2009
- Bobke , T. , Wolf , T. M. Energy Efficiency Equipped Solution by SKF for power train applications - a contribution to CO2-emission reduction and sustainability VDI-Bericht Nr. 2081, VDI Verlag Düsseldorf 2010
- Mayr , F. et al. Antriebsstrang im Spannungsfeld Komforterhöhung und Wirkungsgradoptimierung VDI-Bericht Nr. 1943, VDI Verlag Düsseldorf 2006
- Quintenz , G. , Raedt , H.-W. FEM-optimierte Leichtbau-Hohlwellen für das Getriebe ATZ 12 2009
- Rinderknecht , S. , Rühle , G. , Leitermann , W. Entwicklungspotenzial des Automatisierten Schaltgetriebes ASG in integrierter Bauweise VDI-Bericht Nr. 1704, VDI Verlag Düsseldorf 2002
- Borrmann , D. et al. Der Antriebsstrang mit einem kleinen Downsizing-Motor: Auslegungsstrategien und Systemkomponenten 30. Internationales Wiener Motorensymposium 2009
- Eggert , E. et al. Möglichkeiten und Grenzen des Automatisierten Schaltgetriebes in Serienfahrzeugen IAV GmbH 2003
- Berger , R. , Fischer , R. Parallel-Schalt-Getriebe (PSG) - Doppelkupplungsgetriebe mit Trockenkupplungen VDIBericht Nr. 1704, VDI Verlag Düsseldorf 2002
- Kimmig , K.-L. et al. Kupplungssysteme für hocheffiziente Doppelkupplungsgetriebe VDI Report 2029 VDI Verlag Düsseldorf 2008
- Greiner , J. et al. Kraftstoffsparende Antriebssysteme 30. Internationales Wiener Motorensymposium 2009
- Berger , R. , Meinhard , R. , Bünder , C. The Parallel Shift Gearbox PSG - Twin Clutch Gearbox with Dry Clutches 7. LuK Kolloquium 2002
- Wagner , U. et al. Elektromotorische Automatisierung für Doppelkupplungsgetriebe VDI-Bericht Nr. 1827, VDI Verlag Düsseldorf 2004
- Wagner , U. et al. Trockene Doppelkupplungssysteme - Innovative Komponenten für hocheffiziente Fahrzeuggetriebe ATZ 04 2009
- Berns , S. et al. Reduzierung der CO2- Emissionen bei guter Fahrbarkeit 31. Internationales Wiener Motorensymposium 2010
- Behrendt , M. Entwicklung eines Systemtribometers mit Abbildung mehrachsiger instationärer Beanspruchungskollektive zur Analyse von Reibung und Verschleiß im Mischreibungsgebiet im Kontext nasslaufender Umschlingungs-CVT Dissertation Universität Karlsruhe 2009
- Englisch , A. et al. CVT Komponenten für leistungsverzweigte Nutzfahrzeuggetriebe VDI-Bericht Nr. 1943, VDI Verlag Düsseldorf 2006
- Englisch , A. et al. LuK CVT Komponenten - Die Komponenten für das Getriebe der Zukunft VDI-Bericht Nr. 2029, VDI Verlag Düsseldorf 2008
- Jürgens , G. Vergleich der Verluste bei automatischen Getriebekonzepten VDI-Bericht Nr. 1943, VDI Verlag Düsseldorf 2006
- Papakonstantinou , N. Modellbasierte Optimierung des Betriebs-verhaltens eines Kegel-Ring-Getriebes in einem Kraftfahrzeug Dissertation RWTH Aachen 2007
- Faust , H. , Homm , M. , Bitzer , F. Wirkungsgradoptimiertes CVT-Anpresssystem - Verbrauchsreduktion durch Schlupferhöhung? 7. LuK Kolloquium 2002
- Behrendt , M. Entwicklung eines Systemtribometers mit Abbildung mehrachsiger instationärer Beanspruchungskollektive zur Analyse von Reibung und Verschleiß im Mischreibungsgebiet im Kontext nasslaufender Umschlingungs-CVT Dissertation Universität Karlsruhe 2009
- Albers , A. et al. Keramik als Friktionswerkstoff im CVT- Getriebe VDI-Bericht Nr. 1595, VDI Verlag Düsseldorf 2001
- Englisch , A. CVT - Hochwertig und leistungsstark Schaeffler KOLLOQUIUM 2010
- Tenberge , P. et al. E-CVT - Hybridantrieb mit Umschlingungs-CVT VDI-Berichte Nr. 1943, VDI Verlag Düsseldorf 2006
- Höhn , B.-R. , Pflaum , H. , Tomic , D. Energiebilanzierung und Verbrauchsabschätzung für den optimierten CVT-Hybrid-Antriebsstrang VDI-Berichte Nr. 1943, VDI Verlag Düsseldorf 2006