This content is not included in your SAE MOBILUS subscription, or you are not logged in.
Experimental Research on Mixture Distribution of Diesel Premixed Low-Temperature Combustion
ISSN: 0148-7191, e-ISSN: 2688-3627
Published September 01, 2015 by SAE International in United States
Annotation ability available
The diesel premixed low-temperature combustion mode avoids the generation of thick mixture and the high temperature region in which a great amount of NOx and PM generates. It makes a significant reduction in the emissions of both NOx and PM available at the same time. However, with the quantity of pre-injection increases and the injection time advances, the emission of HC increases significantly, which causes a decrease in the combustion efficiency. Studies have shown that the flame quench caused by too thick or too lean mixture and the oil film on the chamber is the main source for the emission of HC. As a result, understanding the mechanism of atomization and evaporation of the fuel and the formation of the mixture makes significant sense. This paper focuses on the mixture formation process. And the methods of testing the distribution of the mixture, the influential factors and control methods are studied. The results show that single-stage fuel injection leads to much fuel to be adhered on the cylinder wall and forms a thick mixture zone near the wall, which affects the overall level of fuel atomization and uniformity in cylinder. In addition, higher injection pressure, smaller injection pulse and higher cylinder temperature are conducive to the evaporation of diesel and they can help reduce the regions in which the mixture is too thick or too thin. They are important means to improve unburned hydrocarbon (UHC) emissions of the diesel premixed low-temperature combustion.
CitationShi, L., Zhang, L., Deng, K., Lv, X. et al., "Experimental Research on Mixture Distribution of Diesel Premixed Low-Temperature Combustion," SAE Technical Paper 2015-01-1839, 2015, https://doi.org/10.4271/2015-01-1839.
- Su Wanhua , Zhao Hua , Wang Jianxin Theory and Technology of the HCCI Low Temperature Combustion Engine Science Press 2010 215
- Zhao H. HCCI and CAI engines for the automotive industry CRC Press 2007 524
- Johnson , T. Review of Diesel Emissions and Control SAE Int. J. Fuels Lubr. 3 1 16 29 2010 10.4271/2010-01-0301
- Juttu S. , Thipse S. S. , Marathe N. V. etc. Homogeneous Charge Compression Ignition (HCCI): A New Concept for Near Zero NOx and Particulate Matter (PM) from Diesel Engine Combustion[J] SAE paper NO. 2007-26-020 2007
- Heywood J.B. Internal combustion engine fundamentals[J] New York McGraw-Hill 1988
- Lin Tiejian , SU Wan2hua , PEI Yiqiang et al. Effects of Multi-Pulse Injection Parameters on Premixed Diesel Combustion Efficiency and HeatLoss Transactions of CSICE 2004 22 4 325 331
- He Bangquan , Wang Janxin , Hao Jiming et al. Emissions and Catalytic Properties of the Ethanol-Gasoline fuel EFI Gasoline Engine Transactions of CSICE 2002 20 6 529 533
- Paul Miles Sources of CO and UHC in Low-Temperature Diesel Combustion Systems 3rd International Symposium on Clean High-Efficiency Combustion in Engines[C] Tianjin 2008
- Magnus Christensen , Bengt Johansson , Anders Hultqvist The Effect of Piston Topland Geometry on Emissions of Unburned Hydrocarbons from a Homogeneous Charge Compression Ignition (HCCI) Engine [J] SAE paper NO. 2001-01-1893 2001
- Fredrik Wahlin , Andreas Cronhjort , Ulf Olofsson etc. Effect of Injection Pressure and Engine Speed on Air/Fuel Mixing and Emissions in a Pre-Mixed Compression Ignited (PCI) Engine Using Diesel Fuel SAE Paper NO. 2004-01-2989 2004
- Kazuhiro Omae , Yoshimasa Watanabe , Souichi Matsushita etc. Reduction of HC Emission for Passenger Car Diesel Engine SAE Paper NO. 2007-01-0663 2007
- Ma Xiao , He Xu , Wang Jiangxin et al. In-Cylinder mixture Distribution Measurement in a GDI Engine Using Laser-Induced Fluorescence Chinese Internal Combustion Engine Engineering 2010 31 4