This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Low Temperature Thermal Energy Storage (TES) System for Improving Automotive HVAC Effectiveness
Technical Paper
2015-01-0353
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
The prime focus of automotive industries in recent times is to improve the energy efficiency of automotive subsystem and system as whole. Harvesting the waste energy and averaging the peak thermal loads using thermal energy storage (TES) materials and devices can help to improve the energy efficiency of automotive system and sub-system. The phase change materials (PCM) well suit the requirement of energy storage/release according to demand requirement. One such example of TES using PCM is extended automotive cabin comfort during vehicle idling and city traffics including start/stop of the engine at traffic stops.
PCM as TES poses high density and capacity in thermal energy storage and release. It is due to latent heat absorption and release during phase change. Generally the latent heat of a material compare to it sensible heat is much higher, almost an order of 2. For example, latent heat of ice is almost 160 times higher than sensible heat for a kelvin temperature rise of ice.
Using the latent heat capacity of PCM during phase change, an attempt has been made to improve and extend the cabin comfort during city traffics and idling of an automobile. The PCM encapsulated in a heat exchanger is placed in the air path of HVAC AHU system. During the compressor running condition, it uses the cold air coming from evaporator to solidify the encapsulated PCM (charging cycle), this retains the vent temperature within comfortable limit for extended period during the engine shutoff period. This is achieved by releasing the cold energy to air passing through it. Once PCM releases all the latent energy, it converts into liquid state (discharging cycle) and will no longer be able to provide the cooling effect. During engine start it convert back to solid state as stated above. The optimized thermal energy storage system (TESS) with small quantity and high latent heat capacity PCM can improve the effectiveness of automotive HVAC system during traffic stops and engine idling without compromising on the cabin comfort.
In the present work, an attempt has been made to investigate and optimize the extended automobile cabin comfort using TESS having commercial low cost and low temperature PCM as an acting medium. Experiment studies have indicated that the cabin comfort could be extended for almost 41 seconds during engine shut off period.
Recommended Content
Citation
Jha, K. and Badathala, R., "Low Temperature Thermal Energy Storage (TES) System for Improving Automotive HVAC Effectiveness," SAE Technical Paper 2015-01-0353, 2015, https://doi.org/10.4271/2015-01-0353.Also In
References
- Vahid , V. , Bijan , S. , Ahmad , F. , and Kambiz , P. A review of different strategies for HVAC energy saving Energy Conversion and Management 2014 10.1016/j.enconman.2013.10.023
- Jha , K. , Bhanot , V. , and Ryali , V. A Simple Model for Calculating Vehicle Thermal Loads SAE Technical Paper 2013-01-0855 2013 10.4271/2013-01-0855
- Karthik , M. , Patrick , P. , Peter , H. , David , L. et al Experimental investigation of Bio based phase change materials to improve building energy performance ASME 2010 4t h international conference on energy sustainability 2014 10.1115/ES2010-90035
- Kim Ki-bum , Choi Kyung-wook , Kim Young-jin , Lee Ki-hyung et al Feasibility study on a novel cooling technique using a phase change material in an automotive engine Energy 35 2010 478 484 2009 10.1016/j.energy.2009.10.015
- Kalekar , T. and Stechert , C. i-Cool Integration of Phase Change Materials into Metropolitan Car Concepts to Control the Cabin Temperature SAE Technical Paper 2014-28-0044 2014 10.4271/2014-28-0044
- Jamekhorshid , A. and Sadrameli , S.M. application of Phase change materials in maintaining the comfort temperature inside the automobile World Academy of Science, Engineering and Technology 6 2012 01 25 International Science Index 6 1 2012 waset.org/Publication/2587
- Oróa E. , de Graciaa , A. , Castella , M. , Farid , M. M. et al. Review on phase change materials (PCM) for cold thermal energy storage applications Applied Energy 2012 10.1016/j.apenergy.2012.03.058
- Zalbaa , B. , José , M.M. , Cabeza. Lucis F. , and Harald M. Review on thermal energy storage with phase change: materials, heat transfer analysis and applications Applied Thermal Engineering 2003 10.1016/S1359-4311(02)00192-8
- Pluss Polymers http://www.pluss.co.in/pcm.html#Product-Range
- Ralf , M. , Marcus , W. , Boris , K. , and Dieter , H. Storage air conditioning: for hybrid vehicle with automatic start stop function ATZ worldwide 2006 2192-9076