This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Measuring and Comparing the Ignition Delay Times of Diesel, Ethanol Additive and Biodiesel Using a Shock Tube
Technical Paper
2014-36-0187
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
A burning process in a combustion chamber of an internal combustion engine is very important to know the maximum temperature of the gases, the speed of combustion, the ignition delay time of fuel and air mixture exact moment at which ignition will occur. The automobilist industry has invested considerable amounts of resources in numerical modeling and simulations in order to obtain relevant information about the processes in the combustion chamber and then extract the maximum engine performance control the emission of pollutants and formulate new fuels. This study aimed to general construction and instrumentation of a shock tube for measuring shock wave. As specific objective was determined reaction rate and ignition delay time of diesel, biodiesel and ethanol doped with different levels of additive enhancer cetane number. The results are compared with the ignition delay times measured for other authors.
Authors
Citation
Santana, C., Barros, J., Carvalho, M., and de Almeida Junior, H., "Measuring and Comparing the Ignition Delay Times of Diesel, Ethanol Additive and Biodiesel Using a Shock Tube," SAE Technical Paper 2014-36-0187, 2014, https://doi.org/10.4271/2014-36-0187.Also In
References
- ANTONIO , M. C. N. Effect of Piston Gas Pipe / Tunnel Crash When operated in Condition Balance Interface. Thesis presented to the Graduate Division of the Institute of Aeronautical Technology as part of the requirements for obtaining the title of Doctor of Science in Aeronautical Engineering Course in the area of Aeronautics Propulsion and Energy 1997
- CANCINO , L. R. Autoignition of gasoline surrogate mixtures at intermediate temperatures and high pressures: Experimental and numerical approaches Proceeding of the Combustion institute 2009
- MCMILLAN , R.J. Shock tube investigation of pressure and ion sensors used in pulse detonation engine research Thesis of Degree of Master of Science in Aeronautical Engineering 2004
- Campbell , M.F. ; Davidson , D.F. ; Hanson , R.K. and Westbrook , C.K. Ignition delay times of methyl oleate and methyl linoleate behind reflected shock waves Stanford, California, USA 2012
- Cancino , L.R. ; Fikri M. ; Oliveira , A.A.M. ; Schulz , C. Auto ignition of gasoline surrogate mixtures at intermediate temperatures and high pressures: Experimental and numerical approaches Duisburg, Germany 2009
- Davidson , D. F. ; Oehlschlaeger , M. A. ; Herbon , J. T. and Hanson , R. K. Shock Tube measurements of Iso-Octane ignition times and oh concentration time histories High Temperature Gasdynamics Laboratory Mechanical Engineering Department Stanford University Stanford, California, USA 2004
- Davidson , D. F. and Hanson , R. K. Fundamental Kinetics Database Utilizing Shock Tube Measurements, Vol. 1: Ignition Delay Time Measurements Mech. Eng. Dept. Report Stanford University http://hanson.stanford.edu/ California, USA November 2005
- Davidson , D. F. and Hanson , R. K. Fundamental Kinetics Database Utilizing Shock Tube Measurements, Vol. 2: Concentration Time-History Measurements Mech. Eng. Dept. Report Stanford University California, USA December 2006
- Dubois , T. ; Chaumeix , N. and Paillard , C. E. Experimental and Modeling Study of n-Propylcyclohexane Oxidation under Engine-relevant Conditions Total Raffinage Marketing, Direction des Recherches and CNRS Orleans-ICARE, Aérothermique, Réactivité et Enironnement December 5 2008 March 4 2009