This content is not included in your SAE MOBILUS subscription, or you are not logged in.

Numerical Modelling and Experimental Characterization of a Pressure-Assisted Multi-Stream Injector for SCR Exhaust Gas After-Treatment

Journal Article
2014-01-2822
ISSN: 1946-3936, e-ISSN: 1946-3944
Published October 13, 2014 by SAE International in United States
Numerical Modelling and Experimental Characterization of a Pressure-Assisted Multi-Stream Injector for SCR Exhaust Gas After-Treatment
Sector:
Citation: Varna, A., Boulouchos, K., Spiteri, A., Dimopoulos Eggenschwiler, P. et al., "Numerical Modelling and Experimental Characterization of a Pressure-Assisted Multi-Stream Injector for SCR Exhaust Gas After-Treatment," SAE Int. J. Engines 7(4):2012-2021, 2014, https://doi.org/10.4271/2014-01-2822.
Language: English

References

  1. Birkhold , F. , Meingast , U. , Wassermann , P. , and Deutschmann , O. , Analysis of the Injection of Urea-Water-Solution for Automotive SCR DeNOx-Systems: Modeling of Two-Phase Flow and Spray/Wall-Interaction SAE Technical Paper 2006-01-0643 2006 10.4271/2006-01-0643
  2. Birkhold , F. , et al. Modeling and simulation of the injection of urea-water-solution for automotive SCR DeNOx-systems. Applied Catalysis B: Environmental 70 2007 119 127
  3. Jeong , S.J. , Lee S.-J. , and Kim W.-S. Numerical Study on the Optimum Injection of Urea-Water Solution for SCR DeNOx System of a Heavy-Duty Diesel Engine to Improve DeNOx Performance and Reduce NH3 Slip. Environmental Engineering Science 2008 25 7 1017 1035
  4. Ström , H. , Lundström A. , and Andersson B. Choice of urea-spray models in CFD simulations of urea-SCR systems. Chemical Engineering Journal 150 2009 69 82
  5. van Helden , R. , Verbeek , R. , Willems , F. , and van der Welle , R. , Optimization of Urea SCR deNOx Systems for HD Diesel Engines SAE Technical Paper 2004-01-0154 2004 10.4271/2004-01-0154
  6. Spiteri , A.C. and Eggenschwiler P. Dimopoulos Experimental Fluid Dynamic Investigation of Urea-Water Sprays for Diesel SCR-DeNOx Applications. Industrial & Engineering Chemistry Research 2014 53 8 3047 3055
  7. Montenegro , G. and Onorati A. 1D thermo-fluid dynamic modelling of de-NOx SCR systems for diesel engine exhaust gas after-treatment. International Journal of Vehicle Design 2006 41 285 306
  8. Costa , M. , Melo M.J. , and Sousa J.M.M. Spray Characteristics of Angled Liquid Injection into Subsonic Crossflows. AIAA 2006 44 3 646 653
  9. Lee , S.S. , Kim W.H. , and Yoon W.S. Spray formation by a swirl spray jet in low speed cross-flow. Journal of Mechanical Science and Technology 2010 24 2 559 568
  10. Choi , S.M. et al. Spray in Crossflow of a Rotary Atomizer. Atomization and Sprays 2012 22 2 143 161
  11. Panao , M.R. and Moreira A.L.N. Spray Impingement on a Flat Plate Under Cross Flow Conditions ILASS-Europe 2002
  12. Panao , M.R. and Moreira A.L.N. Experimental Characterization of an Intermittent Gasoline Spray Impinging under Crossflow Conditions. Atomization and Sprays 2005 15 201 222
  13. Panao , M.R. , Moreira A.L.N. , and Durao D.F.G. Effect of a cross-flow on spray impingement with port fuel injection systems for HCCI engines. Fuel 106 2013 249 257
  14. Ghosh , S. and Hunt J.C.R. Spray jets in a cross-flow. Journal of Fluid Mechanics 1998 365 109 136
  15. Dekeyser , D. , et al. Assessment of orchard sprayers using laboratory experiments and computational fluid dynamics modelling. Biosystems Engineering 114 2013 157 169
  16. Endalew , A.M. et al. A new integrated CFD modelling approach towards air-assisted orchard spraying. Part I. Model development and effect of wind speed and direction on sprayer airflow. Computers and Electronics in Agriculture 71 2010 128 136
  17. Endalew , A.M. et al. A new integrated CFD modelling approach towards air-assisted orchard spraying-Part II: Validation for different sprayer types. Computers and Electronics in Agriculture 71 2010 137 147
  18. Bade , K.M. , Kalata W. , and Schick R.J. Experimental and Computational Study of a Spray at Multiple Injection Angles ILASS Americas 2010 Cincinnati, Ohio
  19. Arcoumanis , C. and Cutter , P. , Flow and Heat Transfer Characteristics of Impinging Diesel Sprays Under Cross-Flow Conditions SAE Technical Paper 950448 1995 10.4271/950448
  20. Kihm , K.D. , Lyn G.M. , and Son S.Y. Atomization of Cross-Injecting Sprays into Convective Airstream Atomization and Sprays 1995 5 417 433
  21. Arienti , M. , et al. Modeling Wall Film Formation and Breakup Using an Integrated Interface-Tracking/Discrete-Phase Approach. Journal of Engineering for Gas Turbines and Power 2011 133 3
  22. Özdemir , I.B. and Whitelaw J.H. Impingement of an unsteady two-phase jet on unheated and heated flat plates. Journal of Fluid Mechanics 1993 252 499 523
  23. CD-adapco Methodology Star-CD Version 4.16. 2012
  24. Pizza , G. , et al. Evaporating and non-evaporating diesel spray simulation: comparison between the ETAB and wave breakup model. Int. J. Vehicle Design 2007 45 80 99
  25. Reitz , R. and Diwakar , R. , Effect of Drop Breakup on Fuel Sprays SAE Technical Paper 860469 1986 10.4271/860469
  26. Reitz , R. and Diwakar , R. , Structure of High-Pressure Fuel Sprays SAE Technical Paper 870598 1987 10.4271/870598
  27. Reynolds , W.C. et al. Bifurcating and blooming jets. Annual Review of Fluid Mechanics 2003 35 295 315
  28. Fric , T.F. and Roshko A. Vortical structure in the wake of a transverse jet. Journal of Fluid Mechanics 1994 279 1 47
  29. Kelso , R.M. , Lim T.T. , and Perry A.E. An experimental study of round jets in cross-flow. Journal of Fluid Mechanics 1996 306 111 144

Cited By