This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Study on Brake Durability Dynamometer Experimental Method for Brake NVH and Wear
Technical Paper
2014-01-2520
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
A brake durability experimental method is proposed to simulate a brake durability vehicle road test. Brake judder and noise often occur in brake durability road testing. Brake judder is difficult to address because of its many potential causes, such as assembly run out, component stiffness, lining characteristics, thermal coning/hot spot/thermal instability and corrosion. There are currently several test procedures to predict brake thermal roughness and pad cleaning corrosion performance for preventing brake judder. Brake durability vehicle road testing is performed to check brake NVH and wear; examples include the Mojacar test in Spain and the Huangshan test in China. Brake energy intensity and road vibration are the significant factors that cause brake rotor thickness variation, which generates brake judder in public road testing. This study is focused on brake pad wear depending on brake energy intensity and brake rotor temperature to simulate brake durability road testing and brake rotor thickness variation (RTV) generation induced by wear. A brake durability vehicle road test was performed to obtain the initial braking velocity, temperature, deceleration and brake pad wear during the test. A brake rotor temperature curve model and a brake pad wear model were developed on the basis of friction thermodynamics theory and the brake energy intensity wear principle. The brake pad wear and temperature were optimized to be equal to the results of the vehicle road test. A brake durability dynamometer test procedure was developed according to the mathematical model. In this study, the dyno test result is compared with the road result in brake pad wear, brake roughness and propensity for brake noise. The results are shown to be in fairly good agreement.
Recommended Content
| Technical Paper | Brake Squeal and Disc Metallurgy Variability: Importance of Disc Wear |
| Ground Vehicle Standard | Dynamometer Global Brake Effectiveness |
| Journal Article | An Improvement of Brake Squeal CAE Model Considering Dynamic Contact Pressure Distribution |
Authors
Topic
Citation
Wang, Q., Qi, G., Zhang, G., and Pu, X., "Study on Brake Durability Dynamometer Experimental Method for Brake NVH and Wear," SAE Technical Paper 2014-01-2520, 2014, https://doi.org/10.4271/2014-01-2520.Also In
References
- Wang , Q. and Qi , G. , Cui , H.F. Brake Judder Principle and Control on Disk Brake Machinery Design & Manufacture 5 178 179 2010 10.3969/j.issn.1001-3997.2010.05.074
- Yu , Z.P. and Yin , D. X. , Zhang , L.J. et al. A Review on Disk Brake Judder Automotive Engineering 27 3 372 376 2005 10.3321/j.issn:1000-680X.2005.03.029
- Yin , D.X. and Zhang , L.J. , Ning , G.B. et al. Study on The Braking Torque Variation Dynamometer Experimental Journal of Vibration, Measurement & Diagnosis 25 2 117 121 2005 10.3969/j.issn.1004801.2005.02.009
- Meng , D.J. and Zhang , L.J. , Yu , Z.P. Influence of Initial SRO and DTV on Brake Judder Based on Rotor Brake Model With Multi Point Contact Journal Of Vibration And Shock 29 7 43 49 2010 10.3969/j.issn.1000-3835.2010.07.010
- Grochowicz , J. , Ruymen , J. , Abendroth , H. , Augsburg , K. et al. Mojacar Brake Wear and NVH: Dyno Simulation Concept SAE Technical Paper 2007-01-3959 2007 10.4271/2007-01-3959
- Golubev Yu. A. , Ivanenko V. V. A Calculation Method of Energy Intensity of Brake Lining Wear as Related to Temperature Journal of Friction and Wear 30 4 258 260 2009 10.3103/S1068366609040059
- Huang , J.M. and Gao , C.H. , TANG. X.S. etal. Numerical Modeling and Analysis of The Thermal-structure Coupling of The Rotor Brake Chinese Journal of Mechanical Engineering 44 2 145 151 2008 10.3321/j.issn:0577-6686.2008.02.025
- Yang , Z.Y. and Han , J.M. , Li , W.J. et al. Thermo-mechanical coupling simulation of braking process of brake rotor Chinese Journal of Mechanical Engineering 46 2 88 92 2010 10.3901/JME.2010.02.088
- Limpert , R. , Auto Brake System Design and Analyses Beijing China Machine Press 56 58 1985
- Abubakar , A. and Ouyang , H. , Wear Prediction of Friction Material and Brake Squeal Using The Finite Element Method Wear 264 1069 1076 2008 10.1016/j.wear.2007.08.015
- Wang , L.Y. , and Ma , B. , Li , H.Y et al. Research on Wear Calculation Method for Friction Rotor of Wet Shifting Clutch China Mechanical Engineering 19 1 14 17 2008 10.3321/j.issn:1004-132X.2008.01.004
- Riefe , M. and Yen , E. , Prediction of Brake Lining Life Using an Energy-Based CAE Approach SAE Technical Paper 2007-01-1019 2007 10.4271/2007-01-1019
- Lou , G. , Peters , B. , Robere , M. , Severnak , S. et al. Lining Life Prediction Based on Rotor 1-D Thermal Model and Applicability of Wear versus Temperature Data SAE Technical Paper 2008-01-2567 2008 10.4271/2008-01-2567
- Steege , R. , Bauer , G. , and Lange , J. , Life Time Prediction for Brake Linings SAE Technical Paper 2009-01-3027 2009 10.4271/2009-01-3027
- Ferreira , H. , Martinez , R. , Ramos , R. , Ferro , E. et al. Correlation Between Brake Durability Routes: Los Angeles (LACT, USA); Mexico (MCT, Mexico); Sorocaba (SCT, Brazil); P3-19TT (Ford's TPG, Brazil) SAE Technical Paper 2007-01-3953 2007 10.4271/2007-01-3953