This content is not included in your SAE MOBILUS subscription, or you are not logged in.
Single Pulse Jet Impingement on Inclined Surface, Heat Transfer and Flow Field
ISSN: 0148-7191, e-ISSN: 2688-3627
Published September 08, 2013 by SAE International in United States
Annotation ability available
This paper focuses on the heat transfer and flow field resulting from a single pulse impinging jet. The size, time scale and jet characteristics are relevant to automotive diesel injection process. The purpose is to study jet impingement by correlating and cross comparing different measurements and simulations of the same event. The pulse jet impinges on a flat surface at different angles (0°, 30°, 45°, 60°) and a 90° rounded edge.
Experiments are performed deploying various techniques to record the event; PIV for the flow field, high acquisition rate thermocouples and infrared camera for surface temperature. The cases are reproduced with CFD simulations including conjugated heat transfer. The flow is simulated using LES.
The results highlight that the jet penetration rate is a function of the target angle. Also, the heat transfer magnitude and space distribution depends on the surface inclination. Alongside, the consistency of the results validates CFD as a powerful tool to study this type of flow.
CitationBovo, M. and Rojo, B., "Single Pulse Jet Impingement on Inclined Surface, Heat Transfer and Flow Field," SAE Technical Paper 2013-24-0003, 2013, https://doi.org/10.4271/2013-24-0003.
- Jambunethan K., Lai E., Moss M. A. and Button B. L. , A review of heat transfer data for single circular jet impingement, Int. J. Heat and Fluid Flow, Vol. 13, No. 2 106-115
- Viskanta R. , Heat transfer to impinging isothermal gas and flame jets. Experimental Thermal and Fluid Science 6:111-134
- Baughn, J. W. and Shimizu, S. , Heat transfer measurements from a surface with uniform heat flux and an impinging jet, ASME J. Heat Transfer 111/1097.
- Cooper, D., Jackson, D. C., Launder, B. E. & Liao, G. X. 1993 Impinging jet studies for turbulence model assessment-I. Flow-field experiments. Int. J. Heat Mass Transf. 36, 2675-2684.
- Katti, V. and Prabhu, S.V. , Experimental study and theoretical analysis of local heat transfer distribution between smooth flat surface and impinging air jet from a circular straight pipe nozzle, Int. J. Heat Mass Transfer article in press.
- Lytle, D. and Webb, B.W. , Air jet impingement heat transfer at low nozzle plate spacings, Int. J. Heat Mass Transfer 37 1687-1697.
- Gao, N., Sun H. and Ewing D. , Heat transfer to impinging round jets with triangular tabs, Int. J. Heat Mass Transfer 46 2557-2569.
- O'Donovan T. S. and Murray D. B. , Jet impingement heat transfer - Part I: Mean and root-mean-square heat transfer and velocity distributions, Int. J. Heat and Mass Transfer 50 3291-3301.
- O'Donovan T. S. and Murray D. B. , Jet impingement heat transfer - Part II: A temporal investigation of heat transfer and local fluid velocities, Int. J. Heat and Mass Transfer 50 3302-3314.
- Gao N. and Ewing D. , Investigation of the effect of confinement on the heat transfer to round impinging jets exiting a long pipe, Int. J. of Heat and Fluid Flow 27 33-41
- Koseoglu M.F. and Baskaya S. , The effect of flow field and turbulence on heat transfer characteristics of confined circular and elliptic impinging jets, Int. J. of Thermal Sciences article in press.
- Bovo M., Davidson L., “On the transient modelling of impinging jets heat transfer. A practical approach.” proceedings, Turbulence, Heat and Mass Transfer 7, Palermo.
- Yang Yue-Tzu, Tsai Shiang-Yi , Numerical study of transient conjugate heat transfer of a turbulent impinging jet. Heat and Mass Transfer 50 799-807.
- Lien, F.S., Chen, W.L. and Leschziner, M.A. , Low-Reynolds-Number Eddy-Viscosity Modelling Based on Non-linear Stress-Strain/Vorticity Relations, Proc. 3rd Symp. on Engineering Turbulence Modelling and Measurements, Crete, Greece.
- Angiolettia M., Ninoa E., Ruoccob G., CFD turbulent modelling of jet impingement and its validation by particle image velocimetry and mass transfer measurements, International Journal of Thermal Sciences 44 (2005) 349-356
- Bovo M. et al, On the numerical modelling of impinging jet heat transfer, Int. Symp. on Convective Heat and Mass Transfer in Sustainable Energy, 2009, Tunisia
- Hofmann H. M., Kaiser R., Kind M., martin H., Calculations of steady and pulsating impinging jets-an assessment of 13 widely used turbulence models, Numerical heat transfer, part b, 51: 565-583, 2007.
- Hällqvist Thomas 2006, Large Eddy Simulation of Impinging Jets with Heat Transfer KTH Mechanics, SE-100 44 Stockholm, Sweden, dissertation thesis.
- Bovo Mirko & Davidson Lars (2013), On the Numerical Modeling of Impinging Jets, Heat Transfer-A Practical Approach, Numerical Heat Transfer, Part A: Applications: An International Journal of Computation and Methodology, 64:4, 290-316.
- Husberg, T., Gjirja, S., Denbratt, I., Omrane, A. et al., “Piston Temperature Measurement by Use of Thermographic Phosphors and Thermocouples in a Heavy-Duty Diesel Engine Run Under Partly Premixed Conditions,” SAE Technical Paper 2005-01-1646, 2005, doi:10.4271/2005-01-1646.
- Sirignano William A., Fluid Dynamics of Spray - 1992 Freeman Scholar Lecture. Journal of Fluids Engineering, 1993 Vol. 115/345.
- Naber, J. and Siebers, D., “Effects of Gas Density and Vaporization on Penetration and Dispersion of Diesel Sprays,” SAE Technical Paper 960034, 1996, doi:10.4271/960034.
- Siebers D., "Liquid-Phase Fuel Penetration in Diesel Sprays," SAE Technical Paper 980809, 1998, doi:10.4271/980809.
- Abraham, J., “What is Adequate Resolution in the Numerical Computations of Transient Jets?,” SAE Technical Paper 970051, 1997, doi:10.4271/970051.
- Abani Neerev, reitz Rolf D., Modeling sub grid scale mixing of vapor in diesel spray using jet theory, ICLASS 2009, 11th Triennial International Annual Conference on Liquid Atomization and Spray Systems, Vail, Colorado USA.
- Wang, Y., Ge, H., and Reitz, R., “Validation of Mesh- and Timestep- Independent Spray Models for Multi- Dimensional Engine CFD Simulation,” SAE Int. J. Fuels Lubr. 3(1):277-302, 2010, doi:10.4271/2010-01-0626.
- Park Sung Wook, Reitz Rolf D., A gas jet superposition model for CFD modeling of group-hole nozzle sprays, Volume 30, Issue 6, December 2009, Pages 1193-1201.
- Kösters, A. and Karlsson, A., “A Comprehensive Numerical Study of Diesel Fuel Spray Formation with OpenFOAM,” SAE Technical Paper 2011-01-0842, 2011, doi:10.4271/2011-01-0842.
- Azevedo L. F. A., Webb B. W. Queiroz M., Pulsed Air Jet Impingement Heat Transfer Experimental Thermal and Fluid Science, 1994; 8:206-213
- Janetzke Timm, Nitsche Wolfgang, Time resolved investigations on flow field and quasi wall shear stress of an impingement configuration with pulsating jets by means of high speed PIV and a surface hot wire array International Journal of Heat and Fluid Flow 30 (2009) 877-885.
- Xu Peng, Yu Boming, Qiu Shuxia, Poh Hee Joo, Mujumdar Arun S., Turbulent impinging jet heat transfer enhancement due to intermittent pulsation, International Journal of Thermal Sciences 49 (2010) 1247-1252.
- Hofmann Herbert Martin, Movileanu Daniela Luminita, Kind Matthias, Martin Holger, Influence of a pulsation on heat transfer and flow structure in submerged impinging jets, International Journal of Heat and Mass Transfer 50 (2007) 3638-3648.
- Song, L. and Abraham, J., “Influence of Wall Impingement on the Structure of Reacting Jets,” SAE Technical Paper 2003-01-1042, 2003, doi:10.4271/2003-01-1042.
- Pickett, L. and López, J., “Jet-Wall Interaction Effects on Diesel Combustion and Soot Formation,” SAE Technical Paper 2005-01-0921, 2005, doi:10.4271/2005-01-0921.
- Hinze J. O., Turbulence, ISBN 0-07-029037-7
- Baert, R., Klaassen, A., and Doosje, E., “Direct Injection of High Pressure Gas: Scaling Properties of Pulsed Turbulent Jets,” SAE Int. J. Engines 3(2):383-395, 2010, doi:10.4271/2010-01-2253.
- Raffel M., Willert C. & Kompenhans J., Particle Image Velocimetry, A Practical Guide. Springer, 1998. 253 pp. ISBN 3540 63683 8.
- Product Information Coaxial Surface Thermocouple Probes, Medtherm Corporation, Huntsville, Alabama USA
- Osso C. Arroyo, (2009) “Aerothermal Inestigation of an Intermediate Duct”, Thesis for the Degree of Doctor of Philosophy, Chalmers University of Technology.
- Star-ccm+ 7.04.011 userguide by CD-Adapco.
- Jarrin N., Benamadouche S., Laurence D., and Prosser R.. 2006. “A synthetic-eddy-method for generating inflow conditions for large eddy simulations”. International Journal of Heat and Fluid Flow, 27, pp. 585-593.
- Nicoud, F. and Ducros, F., 1999. “Subgrid-Scale Stress Modelling Based on the Square of the Velocity Gradient Tensor,” Flow, Turbulence and Combustion, 62, pp. 183-200.