This content is not included in your SAE MOBILUS subscription, or you are not logged in.
Exhaust Volume Flow based Time Alignment in NOx Measurements in NOx Reduction Systems
ISSN: 0148-7191, e-ISSN: 2688-3627
Published September 24, 2012 by SAE International in United States
Annotation ability available
With the emission norms becoming more and more stringent along with the focus on reducing ownership and operating costs, the need to optimize the aftertreatment system becomes much more evident. Thus, the well monitored, optimized usage of urea or ammonia (NH₃) for the NOx reduction in an SCR system is critical to reduce the operating cost of the vehicles and to comply with emission regulations. In Ammonia Storage and Delivery System (ASDS), pure gaseous NH₃ from the NH₃ cartridges is being used for the reduction of the engine-out NOx in the exhaust stream over the NPF (NOx Particulate Filter). In almost all NOx reduction systems, NOx sensors play an important role in determining the amount of urea or NH₃ to be dosed for efficient NOx reduction with minimal NH₃ consumption and slippage for best possible fluid economy. In the NH₃ dosing strategy the NOx conversion efficiency plays a vital role as a feedback variable for calculating NH₃ dosing quantity and is based on the upstream and downstream NOx sensor measurements. Since the NOx sensors are separated by certain volume of aftertreatment, there is a time delay involved in the measurements. This paper discusses about the importance of the time delay correction needed in NOx measurements between engine-out (pre-aftertreatment system) and tail pipe-out (post-aftertreatment system) locations for the effective implementation of the NH₃ dosing strategy. This is particularly important when the dosing strategy is in feed-forward mode purely based on NOx sensors measurement with no ammonia storage and during transient engine operation.
CitationSubramanian, V., Singh, N., and Lack, A., "Exhaust Volume Flow based Time Alignment in NOx Measurements in NOx Reduction Systems," SAE Technical Paper 2012-01-1959, 2012, https://doi.org/10.4271/2012-01-1959.
- Jääskeläinen, Hannu, Diesel Exhaust Gas, Majewski, W. Addy, Selective Catalytic Reduction, Dieselnet.
- Johnson, T., “Diesel Emissions in Review,” SAE Int. J. Engines 4(1):143-157, 2011, doi:10.4271/2011-01-0304.
- Santhanam, Shyam, Adelman, Brad & Derybowski, Ed, Integration and Testing of an Ammonia Storage and Delivery System to an Engine/Vehicle for NOx Reduction, APAC16 Paper No. M20100158, SAE, India.
- Johannessen, T., Schmidt, H., Svagin, J., Johansen, J. et al., “Ammonia Storage and Delivery Systems for Automotive NOx Aftertreatment,” SAE Technical Paper 2008-01-1027, 2008, doi:10.4271/2008-01-1027.
- Kawakami, A., Mizutani, T., Shibagaki, Y., Yuuki, K. et al., “High Porosity DPF Design for Integrated SCR Functions,” SAE Technical Paper 2012-01-0843, 2012, doi:10.4271/2012-01-0843.
- Wurzenberger, J., Wanker, R., and Schüßler, M., “Simulation of Exhaust Gas Aftertreatment Systems - Thermal Behavior During Different Operating Conditions,” SAE Technical Paper 2008-01-0865, 2008, doi:10.4271/2008-01- 0865.
- Desai, M., Tutuianu, M., Ahmadinejad, M., Watling, T. et al., “Modeling of Non-Road Diesel Exhaust Aftertreatment Systems: Diesel Oxidation and Selective Catalytic Reduction Catalysts,” SAE Technical Paper 2010-01-2092, 2010, doi:10.4271/2010-01-2092.