This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Electromagnetically Compatible Solutions for High and Low Frequency Environment by Separation of Systems
Technical Paper
2012-01-0787
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
Hybrid electric vehicles require careful dealing with EMC because in HEV's analog and digital circuitry coexist in the vehicle's enclosed environment. These lead to a requirement of advanced methods for the increased requirements for electromagnetic compatibility and analysis and reduction of EMI [1]. There are many methods to increase EMI resistance of a hybrid car's electronics systems implemented printed circuit board, several of which will be reviewed in the current paper. In this review paper, we explain conducted and radiated emission avoidance methods using isolation amongst several subsystems. Within the harsh EM environment of a modern hybrid car, isolation between systems of differing frequencies is an effective method for reducing EMI/EMC issues. These techniques include usage of filters to hinder conducted emissions and shielding to stop radiated emissions. Of the many parameters which need to be tweaked to improve the electromagnetic compatibility of a system, the use of filters at the boundaries of shielded systems (to increase resistance to RF and transient susceptibility issues). In hybrid electric vehicles, electronic power converters produce EM noise with high-powered low frequency harmonics and high-frequency low powered electronic noise is produced from in-vehicle communication systems. More research is required in the field where there is a requirement to separate devices operating at high and low frequency spectrum ranges at the same time. We attempt to show several solutions to these class of EMI problems present in mixed frequency environments through the use of separation of systems. [2] [3]
Recommended Content
Authors
Topic
Citation
Raza, A., ali, S., shafqat, A., Mushtaq, A. et al., "Electromagnetically Compatible Solutions for High and Low Frequency Environment by Separation of Systems," SAE Technical Paper 2012-01-0787, 2012, https://doi.org/10.4271/2012-01-0787.Also In
References
- Lee, Y. H. Nasiri, A. “Analysis and modeling of conductive EMI noise of power electronics converters in electric and hybrid electric vehicles,” Applied Power Electronics Conference and Exposition, 2008. APEC 2008. Twenty-Third Annual IEEE 1952 1957 2008
- Hanigovszki, N. Landkildehus, J. Spiazzi, G. Blaabjerg, F. “An EMC evaluation of the use of unshielded motor cables in AC adjustable speed drive applications,” IEEE Transactions on Power Electronics 21 1 273 281 2006
- Bucker, M. “EMI behavior of copper areas on outer layers of PCBs,” IEEE International Symposium on Electromagnetic Compatibility, 2000 1 477 482 2000
- Ott, H. W. Electromagnetic compatibility engineering Hoboken, New Jersey John Wiley & Sons, Inc. 2009
- US Code of Federal Regulations, Title 47, Part 15, Subpart B 2005
- Paul, C. R. Intorduction to Electromagnetic Compatibility Hoboken, New Jersey John Wiley & Sons, Inc. 2006
- Robinson, M. Benson, T. Christopoulos, C. Dawson, J. Ganley, M. Marvin, A. Porter, S. Thomas, D. Turner, J. “Effect of logic family on radiated emissions from digital circuits,” IEEE Transactions on Electromagnetic Compatibility 40 3 288 293 Aug 1998
- Paul, C. R. “Printed Circuit Board Design,” Introduction to Electromagnetic Compatibility New York John Wiley and Sons, Inc. 1992
- Armstrong, M. “PCB design techniques for lowest-cost EMC compliance,” Electronics & Communication Engineering Journal 11 5 1999
- German, R. Ott, H. Paul, C. “Effect of an image plane on printed circuit board radiation,” IEEE International Symposium on Electromagnetic Compatibility Washington, DC August 1990
- Ott, H. “Controlling EMI by proper printed wiring board layout,” Proceedings of the 1985 International Symposium on Technical Exhibition on Electromagnetic Compatibility Zurich, Switzerland March 1985
- Paul, C. R. “Modeling electromagnetic interference properties of printed circuit boards,” IBM Journal of Research and Development 33 33 50 1989
- Smith, T. Paul, C. “Effect of grid spacing on the inductance of ground grids,” Proceedings of the 1991 IEEE International Symposium on Electromagnetic Compatibility Cherry Hill, New Jersey August 1991
- Moongilan, D. “Grounding optimization techniques for controlling radiation and crosstalk in mixed signal PCBs,” IEEE International Symposium on Electromagnetic Compatibility 1 495 500 Aug 1998
- Moongilan, D. “Skin effect modeling of image plane techniques for radiated emissions from PCB traces,” IEEE 1997 International Symposium on EMC 308 313 1997
- Faraji-Dana, Y. C. R. “The current distribution and AC resistance of microstrip structure,” IEEE Transactions on Microwave Theory and Technology 9 1268 1277 September 1990
- Gravelle, L. Wilson, P. “EMI/EMC in printed circuit boards-a literature review,” IEEE Transactions on Electromagnetic Compatibility 24 2 109 116 1992
- Hubing, T. “PCB EMC design guidelines: a brief annotated list,” 2003 IEEE International Symposium on Electromagnetic Compatibility 1 34 36 2003
- Ott, H. “Ground path for current flow,” Proceedings 1979 IEEE International Symposium on Electromagnetic Compatibility 1979
- Ott, H. Noise Reduction Techniques in Electronic Systems Second New York John Wiley Interscience 1988
- Ott, H. “Digital circuit grounding and interconnection,” Proceedings 1981 IEEE International Symposium on Electromagnetic Compatibility 1981
- Tarui, Y. Watanabe, K. Sakusabe, T. Takahashi, T. Schibuya, N. “EMC constraint PCB design support tool-assistance for power and ground trace wiring,” 1999 International Symposium on Electromagnetic Compatibility 564 567 1999
- Chen, G. K. C. Whalen, J. J. “Comparative RFI performance of bipolar operational amplifiers,” IEEE Transactions on Electromagnetic Compatibility 22 91 95 1987
- Morrison, R. Grounding and Shielding Techniques in Instrumentation New York John Wiley 1967
- Bush, D. “A simple way of evaluating the shielding effectiveness of small enclosures,” 8th International Symposium and Technical Exhibition on Electro-magnetic Compatibility Zurich, Switzerland March 1989
- Kerns, D. “Integrated circuit construction and its effects on EMC performance,” Proceedings of the 1984 IEEE International Symposium on Electromagnetic Compatibility San Antonio, Texas April 1984
- German, R. “Use of a ground grid to reduce printed circuit board radiation,” Proceedings of the 1985 International Symposium and Technical Exhibition on Electromagnetic Compatibility Zurich, Switzerland March 1985
- Skilling, H. Electric Transmission Lines New York McGraw-Hill 1951
- Engelbrecht, J. Hermes, K. “A study of decoupling capacitors for EMI reduction, 7R-51.0152,” Technical Report, International Business Machines May 1984
- Hoer, C. Love, C. “Exact inductance equations for rectangular conductors with applications to more complicated geometries,” J. Research Natl. Bur. Stand.-C. Eng. Instrum 69C 127 137 1965
- Ruehli, A. E. “Inductance calculations in a complex integrated circuit environment,” IBM Journal of Research and Develpoment 16 470 481 1972