This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Dynamic Friction Measurements, Especially for High Power Applications
Technical Paper
2011-01-2373
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
Dynamic aspects in the understanding of friction are increasingly coming into focus. Therefore, test arrangements are required, which allow dynamic measurements as well, especially with defined and reproducible sliding speeds. In addition, investigations of vehicle brakes require high power. A simple, reliable measurement device, based on the pin-on-disc principle, that meets these requirements was developed and will be presented here.
This high load tribometer is based on a specially altered lathe. One key benefit of a lathe as a basic unit is the fact that the main mechanical part is standardized industrial equipment. Additional components and measuring devices can be integrated with little effort and great flexibility. The built-in 15kW AC motor and the embedded gearbox permit speeds and torques to the service areas of vehicle brakes, also of heavy duty vehicles and sports cars. The forces can be measured either with a 3-axes strain gauges sensor or a 3-axes piezoelectric sensor directly at the sample.
The high load tribometer is a suitable tool to investigate fundamental questions of tribology. It also allows investigations close to a full brake system under reproducible experimental conditions. With its high flexibility, many different tests are conceivable, e.q. friction tests under the influence of lubricants or the behavior under defined load or speed changes.
This paper introduces this new device and presents its design in detail. Some sample measurements under different conditions and a correlation with full scale brake dynamometer tests will be presented.
Recommended Content
Technical Paper | Recent Developments in Pneumatic Starters for Jet Engines |
Technical Paper | Analysis of Roller-Follower Valve Gear |
Technical Paper | Vibration Reduction Applying Skew Phenomena of Needle Roller Bearings in Brake Actuators |
Citation
Ostermeyer, G. and Perzborn, N., "Dynamic Friction Measurements, Especially for High Power Applications," SAE Technical Paper 2011-01-2373, 2011, https://doi.org/10.4271/2011-01-2373.Also In
References
- Steinhilper, W. Sauer, B. Konstruktionselemente des Maschinenbaus 6 Springer 2008
- Ostermeyer, G. “Dynamic Friction Laws and Their Impact on Friction Induced Vibrations,” SAE Technical Paper 2010-01-1717 2010 10.4271/2010-01-1717
- Perzborn, N. Ostermeyer, G.-P. On the description and measurement of the friction coefficient in models of multibody dynamics GAMM 2011
- Breuer, B. Bill, Kh.H. Bremsenhandbuch 3 Vieweg 2006
- Reif, K. Bremsen und Bremsregelsysteme Vieweg 2010
- ZMM Sliven AG: User manual
- Kistler Instrumente AG Winterthur Betriebsanleitung, 3-Komponenten-Kraftsensor Typen 9251A, 9252A, 9250A4, 9251A Kistler AG 1999
- Kistler Instrumente AG Winterthur Betriebsanleitung, Mehrkanal-Ladungsverstärker Typ 5019B Kistler 1998
- Yokogawa Electric Corporation DL750 Digital-Ozilloskop, Benutzerhandbuch
- Kistler Instrumente AG Winterthur Betriebsanleitung, Mehrkanal-Ladungsverstärker Typ 5019B Kistler 1998
- Kistler Gruppe, Winterthur Kabel, Für Kraft-, Drehmoment- und Dehnungssensoren Kistler 2008
- Deters, L. Fischer, A. Santner, E. Stolz, U. GfT Arbeitsblatt 7: Tribologie - Verschleiß, Reibung, Definitionen, Begriffe, Prüfung, Gesellschaft für Tribologie e.V. 2002
- Ostermeyer, G.-P. Thesen zur Modellierung von Reibung und Verschleiß Jahrestagung GfT 2002