This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Analysis of Lightweighting Design Alternatives for Automotive Components
Technical Paper
2011-01-2287
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
Gasoline-powered vehicles compose the vast majority of all light-duty vehicles in the United States. Improving fuel economy is currently a topic of great interest due to the rapid rise in gasoline costs as well as new fuel-economy and greenhouse-gas emissions standards. The Chevrolet Silverado is currently one of the top selling trucks in the U.S. and has been previously modeled using the commercial finite element code LS-DYNA by the National Crash Analysis Center (NCAC). This state-of the art model was employed to examine alternative weight saving configurations using material alternatives and replacement of traditional steel with composite panels. Detailed mass distribution analysis demonstrated the chassis assembly to be an ideal candidate for weight reduction and was redesigned using Aluminum 7075-T6 Alloy and Magnesium Alloy HM41A-F. Finite element analysis demonstrated that both the Aluminum and Magnesium configurations are feasible alternatives, allowing a weight reduction of 60% and 70% respectively of the original chassis design while reducing overall stress through the model and consequently providing a higher factor of safety. The truck bed and rear floor panels were redesigned using lightweight composite panels consisting of aramid/phenolic honeycomb cores with polyester/glass fiber face plates. The sandwich structures were modeled using LS-DYNA with two approaches. While both employ shell elements for the faceplates, the first simplifies the core using solid elements and the effective orthotropic material parameters while the second offers a more comprehensive depiction of the hexagonal core cells with shell elements. The dynamic behavior analysis of the composite panels incorporated into the Silverado model was also performed using LS-DYNA. When combined, aluminum chassis alternative with replaced composite panels offer a significant weight saving for the Chevrolet Silverado. Furthermore, the composite panels designed can be adapted for heavy-duty vehicles where a greater impact on fuel economy would be provided.
Recommended Content
Technical Paper | Design, Fabrication and Stress Analysis of a Composite Propeller Shaft |
Technical Paper | Identification of Dry Sliding Wear Behavior of B 4 C P Particulate Reinforced Mg Matrix Composites for Automobile Disk Brakes |
Progress In Technology | Aluminum Auto-Body Joining |
Authors
Topic
Citation
William, G., Shoukry, M., and Prucz, J., "Analysis of Lightweighting Design Alternatives for Automotive Components," SAE Technical Paper 2011-01-2287, 2011, https://doi.org/10.4271/2011-01-2287.Also In
References
- U.S. Environmental Protection Agency 2007 “Light-Duty Automotive Technology and Fuel Economy Trends: 1975 through 2007.” EPA420-R-07-008 Office of Transportation and Air Quality
- Bandivadekar, A. Bodek, K. Cheah, L. Evans, C. Groode, T. Heywood, J. Kasseris, E. Kromer, M. Weiss, M. 2008 “On the Road in 2035: Reducing Transportation's Petroleum Consumption and GHG Emissions.” Report No. LFEE 2007-04 RP Laboratory for Energy and the Environment, Massachusetts Institute of Technology Massachusetts, USA
- Reinforced Plastics 2005 “$70m for Materials to Reduce Car Weight.” Reinforced Plastics 53 3 16
- Schewel, L. “Triple Safety: Lightweighting Automobiles to Improve Occupant, Highway, and Global Safety,” SAE Technical Paper 2008-01-1282 2008 10.4271/2008-01-1282
- Cheah, L. Evans, C. Bandivadekar, A. Heywood, J. 2007 “Factor of Two: Halving the Fuel Consumption of New U.S. Automobiles by 2035.” Report No. LFEE 2008-05 RP Laboratory for Energy and the Environment, Massachusetts Institute of Technology Massachusetts, USA
- Forschungsgesellschaft, Kraftfahrwesen mbH Aachen 2007 “Determination of Weight Elasticity of Fuel Economy for Conventional ICE Vehicles, Hybrid Vehicles and Fuel Cell Vehicles.” Final Report No. 55510 International Iron and Steel Institute, WorldAutoSteel Middletown, Ohio, USA
- Pagerit, S. Sharer, P. Rousseau, A. “Fuel Economy Sensitivity to Vehicle Mass for Advanced Vehicle Powertrains,” SAE Technical Paper 2006-01-0665 2006 10.4271/2006-01-0665
- Du Bois, P. Chou, C.C. Fileta, B.B. Khalil, T.B. King, A.I. Mahmoud, H.F. Mertz, H.J. Wismans, J. 2004 “Vehicle Crashworthiness and Occupant Protection.” Prasad, P. Belwafa, J.E. American Iron and Steel Institute Southfield, Michigan, USA
- Daimler HighTech Report 2008 “Designs for Tomorrow New Inspiration from the Mercedes-Benz Advanced Design Studio in California.” The Fascination of Technology , Issue 01/2008
- Lavender, C.A. Knop, K.M. Eberhardt, J.J. 2006 “New-Generation Frame for Pickup/Sport Utility Vehicle Application.” FY 2006 Progress Report for High Strength Weight Reduction Materials Office of FreedomCAR and Vehicle Technologies, U.S. Department of Energy Washington, C.C., USA 119 121
- IBIS Associates, Inc. 2008 “Aluminum Vehicle Structure: Manufacturing and Lifecycle Cost Analysis Hybrid Drive and Diesel Fuel Vehicles.” Research Report 2008-05 The Aluminum Association Arlington, Virginia, USA
- Schultz, R. 2008 2009 update on North American light vehicle aluminum content compared to the other countries and regions of the world-Phase II: Ducker Worldwide LLC, 96 Power point Slides
- Institut fur Kraftfahrzeuge 2010 “Stiffness Relevance and Strength Relevance in Crash of Car Body Components.” Report No. 83440 European Aluminum Association Brussels, Belgium
- Tolani, N.M. Eberhardt, J.J. 2007 “Application of Superplastically Formed Aluminum for Truck Body Panels.” FY 2006 Progress Report for High Strength Weight Reduction Materials Office of FreedomCAR and Vehicle Technologies, U.S. Department of Energy Washington, C.C., USA 111 114
- United States Automotive Materials Partnership 2006 “Magnesium Vision 2020: A North American Automotive Strategic Vision for Magnesium.” U.S. Council for Automotive Research LLC Southfield, Michigan, USA
- Nyberg, E. 2007 “Magnesium Research and Technology Development.” FY 2006 Progress Report for Automotive Lightweighting Materials Office of FreedomCAR and Vehicle Technologies, U.S. Department of Energy Washington, C.C., USA i95 i97
- Osborne, R. 2007 “Structural Cast Magnesium Development.” FY 2006 Progress Report for Automotive Lightweighting Materials Office of FreedomCAR and Vehicle Technologies, U.S. Department of Energy Washington, C.C., USA i54 i65
- Luo, A.A. 2007 “Magnesium Front End.” FY 2006 Progress Report for Automotive Lightweighting Materials Office of FreedomCAR and Vehicle Technologies, U.S. Department of Energy Washington, C.C, USA i89 i94
- Maj, M.H. 2007 “Ultra-Large Castings of Aluminum and Magnesium.” FY 2006 Progress Report for Automotive Lightweighting Materials Office of FreedomCAR and Vehicle Technologies, U.S. Department of Energy Washington, C.C., USA i75 i84
- Calmeson
- Kaw, A.K. 2006 “ Mechanics of Composite Materials-Second Edition .” CRC Press, Taylor and Francis Group Boca Raton, Florida, USA
- Mangino, E. Carruthers, J. Pittaresi, G. 2007 “The Future Use of Composite Materials in the Automotive Industry.” International Journal of Vehicle Design 44 3-4 211 232
- Stewart, R. 2009 “Lightweighting the Automotive Market.” Reinforced Plastics 49 6 14 21
- National Crash Analysis Center 2009 “Finite Element Model of Chevy Silverado- Model Year 2007 Version 2.” Federal Highway Administration/National Highway Traffic Safety Administration
- Mohan, P. Marzougui, D. Arispe, E. Story, C. 2009 “Component and Full-Scale Tests of the 2007 Chevrolet Silverado Suspension System.” Report No. DTFH61-02-X-00076 Federal Highway Administration McLean, Virginia, USA
- Codd, D. 2008 “Advanced Lightweight Materials, Development and Technology for Increasing Vehicle Efficiency.” KVA, Incorporated Escondido, California, USA
- Carpenter, J. Smith, M. Warren, D. 2005 “Research Needs in Predictive Engineering of Advanced Composite Materials.” Pacific Northwest National Laboratory, U.S. Department of Energy USA