This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
A Simple Physical Model of ICE Mechanical Losses
Technical Paper
2011-01-0610
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
The current state-of-the-art offers two extremes of engine mechanical loss models: pure empirical models, using, e.g., regression models based on experimental results, and full-sized 3-D hydrodynamic friction models, solving Reynolds-like lubrication equations for complicated geometry of piston ring/cylinder liner or load-distorted shapes of crankshaft/connecting rod bearings and journals. Obviously, the former method cannot be reliably extrapolated while the latter is too complicated, especially for the early stage of design.
The aim of the current paper is describing the development and experimental calibration of the physical cranktrain model for FMEP prediction, based on simplified phenomenological model of mixed friction. The model uses simply defined shapes of Stribeck curves (friction coefficient) in dependence on Sommerfeld number, i.e., on effective sliding velocity, oil viscosity, dimension scaling factor and the normal force load. The piston rings are loaded by pre-tension and by pressure difference at external and internal surfaces. The instantaneous pressures at ring-pack are simulated using GT Power modules. Forces and torques in the cranktrain are calculated iteratively taking into account the additional friction effects and the non-uniformity of crank speed, reflected by inertia forces.
The model has been calibrated using data from engine tests at different loads, speeds and oil/cooling water temperature levels. The experimental FMEP was found by comparison of IMEP and engine torque. Top dead centre position of the piston was corrected according to the thermodynamic results. The calibration itself is done applying optimization methods for finding the best fit to experimental values, using different load and speed conditions. The sensitivity of model parameters to load conditions is tested in advance, yielding hints to the arrangement of experiments. The same approach is being applied to the valve gear and injection pump torque estimation.
The results show the predictive accuracy better than four percent considering mechanical efficiency.
Recommended Content
Technical Paper | Achieving Optimum Crankshaft Design - I |
Journal Article | Fundamental Analysis of Spring-Varied, Free Piston, Otto Engine Device |
Technical Paper | Development of an Engine Oil Temperature Prediction Method Using 3D Model Simulation |
Authors
Citation
Macek, J., Fuente, D., and Emrich, M., "A Simple Physical Model of ICE Mechanical Losses," SAE Technical Paper 2011-01-0610, 2011, https://doi.org/10.4271/2011-01-0610.Also In
References
- Nozawaa, R. Moritaa, Y. Shimizu, M. Effects of engine downsizing on friction losses and fuel economy Tribology International 27 1 0301-679X Elsevier B.V. 31 37 February 1994
- Heywood, J. B. Internal Combustion Engine Fundamentals McGraw-Hill, Inc. 1998 712 747 0-07-028637-X
- Kobayashi, M. Tanabe, T. Ushijima, K. Aoyama, S. “A Lubrication Analysis of Multi Link VCR Engine Components using Mixed Elasto-Hydrodynamic Lubrication Theory Model,” SAE Technical Paper 2009-01-1062 2009 10.4271/2009-01-1062
- Novotný, P. Ambróz, R. Píštěk, V. Friction loss analysis of powertrain parts Mecca 02 2009 1214-0821 2009
- Pipitone, E. “A New Simple Friction Model for S. I. Engine,” SAE Technical Paper 2009-01-1984 2009 10.4271/2009-01-1984
- Sandoval, D. Heywood, J. B. “An Improved Friction Model for Spark-Ignition Engines,” SAE Technical Paper 2003-01-0725 2009 10.4271/2003-01-0725
- Macek, J. Remek, B. Simplified Model of Losses in Crank Gear MOTORSYMPO '99 1 Praha ČVUT, Fakulta strojní 1999 11 21 80-01-01985-3
- Sethu, C. Leustek, M. Bohac, S. Filipi, Z. Assianis, D. “An Investigation in Measuring Crank Angle Resolved In-Cylinder Engine Friction Using Instantaneous IMEP Method,” SAE Technical Paper 2007-01-3989 2007 10.4271/2007-01-3989
- Isarai, R. Sugino, M. Moritsugu, M. Kato, N. Nakamura, M. “Strain and Motion Measurement for Piston, Piston Ring and Connecting Rod of High Speed Running Engines using New Digital Telemeter,” SAE Technical Paper 2008-01-1042 2008 10.4271/2008-01-1042
- Shayler, P. Allen, A. Leong, D. Pegg, I. Brown, A. Dumenil, J-C. “Characterizing Lubricating Oil Viscosity to Describe Effects on Engine Friction,” SAE Technical Paper 2007-01-1984 2007 10.4271/2007-01-1984
- Gamma Technologies, Inc. Software GT-POWER User's Manual version 6.2 September 2006
- Dursunkaya, Z. Keribar, R. Richardson, D. “Experimental and Numerical Investigation of Inter-Ring Gas Pressures and Blowby in a Diesel Engine,” SAE Technical Paper 930792 1993 10.4271/930792
- Nilsson, Y. Eriksson, L. “Determining TDC Position Using Symmetry and Other Methods,” SAE Technical Paper 2004-01-1458 2004 10.4271/2004-01-1458
- Pipitone, E. Beccari, A. Beccari, S. “The Experimental Validation of a New Thermodynamic Method for TDC Determination,” SAE Technical Paper 2007-24-0052 2007 10.4271/2007-24-0052
- Pipitone, E. Beccari, A. Beccari, S. “Reliable TDC Position Determination: A Comparison of Different Thermodynamic Methods through Experimental Data and Simulations,” SAE Technical Paper 2008-36-0059 2008 10.4271/2008-36-0059
- Fuente, D. Friction Measurements of Sleeve Valve Engine in the Piston/Sleeve Interfaces MSc Thesis Cranfield University 2009
- Macek, J. A simplified model of a valve gear with friction XXX. Conference of Engine Research, CTU in Prague Prague 1999 17 27 80-01-01972-1