This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Performance Evaluation of Three-Stage Turbocharging System for Heavy-Duty Diesel Engine
Technical Paper
2011-01-0374
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
An exhaust turbocharging system makes it possible to increase the brake mean effective pressure (BMEP) and lower emissions levels for a diesel engine while further improving the thermal efficiency. However, in order to meet future emission regulations, further reductions in NOx and particle matter (PM) emissions are necessary. In addition, the diesel engine should have further reductions in fuel consumption to reduce CO₂, which is one of the main greenhouse gases.
Authors participated in a program for the comprehensive technological development of innovative, next-generation, low-pollution vehicles with the New Energy and Industrial Technology Development Organization (NEDO) from 2004 through 2008 in cooperation with the National Institute of Advanced Industrial Science and Technology (AIST). A low-emission and high-efficiency diesel engine system was developed to meet the target of NEDO project.
The turbocharging system which makes possible the high boost and high exhaust gas recirculation (EGR) rate was evaluated by using simulation. Thus, the sequential three-stage turbocharging system was proposed and the engine that was equipped with this turbocharging system was tested. Finally, the project target was achieved by the three-stage turbocharging system with the combined use of the exhaust aftertreatment system. This paper describes the simulation evaluation of the turbocharging systems, which was developed as an elemental technology in the NEDO project, and test results on the improvement in the tradeoff between NOx emission and fuel consumption.
Recommended Content
Authors
Topic
Citation
Nitta, J., Minato, A., and Shimazaki, N., "Performance Evaluation of Three-Stage Turbocharging System for Heavy-Duty Diesel Engine," SAE Technical Paper 2011-01-0374, 2011, https://doi.org/10.4271/2011-01-0374.Also In
References
- NEDO HP http://www.nedo.go.jp/informations/koubo/160601_2/16060l_2.html
- Takada, K. Kusaka, J. Numerical Analysis in Mechanism of Diesel Combustion That Achieves Both High Thermal Efficiency and Low NOx Emission Characteristics with EGR and Supercharge Proc. of Japan SAE, 20085368
- Suzuki, H. Minato, A. Kitabatake, R. Shimazaki, N. Improvement of the Combustion in a Conventional Combustion Region with the Ultra High Pressure Injection System Proc, of Japan SAE, 20085730
- Minato, A. Nitta, J. Shimazaki, N. Performance Evaluation of 3-stage Boosting Diesel Engine by using the Total Engine Simulation System Trans. of japan SAE 2009 40 3 823 829
- Millo, F. Mallamo, F. Ganio Mego, G. “The Potential of Dual Stage Turbocharging and Miller Cycle for HD Diesel Engines,” SAE Technical Paper 2005-01-0221 2005 10.4271/2005-01-0221
- Arnold, S. Calta, D. Dullack, K. Judd, C. et al. “Development of an Ultra-High Pressure Ratio Turbocharger,” SAE Technical Paper 2005-01-1546 2005 10.4271/2005-01-1546
- Arnold, S. “Single Sequential Turbocharger : A New Boosting Concept for Ultra-Low Emission Diesel Engines,” SAE Int. J. Engines 1 1 232 239 2008 10.4271/2008-01-0298
- Galindo, J. Climent, H. Guardiola, C. Ben, H. Azoulay, D. Sequential Two-Stage Turbocharging Specifications for an Automotive HCCI Engine FISITA2008
- Obuchi, A. Uchisawa, Junko Nanba, T. Ohi, A. Iijima, N. Masukawa, S. Tsujimura, T. Development of an internal heat-exchanging converter for the purification of diesel vehicle exhausts gas - Performance of a prototype converter installing a Cu-zeolite catalyst for the selective reduction with NH3 Proc. of Japan SAE, 20095036