This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
CFD Study of Spray Design for a GDI High Performance 2-Stroke Engine
Technical Paper
2010-32-0014
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
The advantages of 2-stroke engines, high power and low weight, are in conflict with their disadvantages, high emissions and bad fuel economy. As these disadvantages are caused by the scavenging process, a reason for the problem can be analyzed by using three dimensional computational fluid dynamics simulation (3D CFD simulation). The scavenging losses can be dramatically reduced with a high pressure fuel injection strategy. The purpose of this strategy is to prevent a fuel concentration in the incoming charge and to reduce the fuel concentration inside the exhaust system. These advantages can only be successfully exploited with the application of an optimal injection strategy.
This paper covers a spray study for a gasoline direct injection (GDI) high performance 2-stroke engine using the commercial CFD Code Fluent. The simulations were conducted for four different engine operating points and the test bench results of the fired engine were used for the validation of the gas dynamic behavior simulation inside the engine. The main focus of the present paper lies on the simulation methodology used for the fuel injection simulation. The used injection settings and their validation results are presented and discussed in detail. The assessment and definition of the best injection strategy for a 2-stroke engine at high engine speed is a demanding task and presented in this paper.
Recommended Content
Authors
Topic
Citation
Jajcevic, D., Almbauer, R., Schmidt, S., Glinsner, K. et al., "CFD Study of Spray Design for a GDI High Performance 2-Stroke Engine," SAE Technical Paper 2010-32-0014, 2010, https://doi.org/10.4271/2010-32-0014.Also In
References
- Trescher, D. “Development of an Efficient 3-D CFD Software to Simulate and Visualize the Scavenging of a Two-Stroke Engine” Archives of Computational Methods in Engineering 67 111 10.1007/s11831-007-9014-6 2007
- Jajcevic, D. Almbauer, R.A. Schmidt, S. P. Glinser, K. “Simulation Strategy and Analysis of a Two-Cylinder Two Stroke Engine Using CFD Code Fluent” European Automotive Simulation Conference (EASC) 2009
- Groth, K. “Das Betriebsverhalten des schnellaufenden Zweitakt-Ottomotors mit Einspritzung und seine Entwicklungsmöglichkeiten” VDI-Verlag Düsseldorf 1959
- Schmidt, S. Winkler, F. Schoegl, O. Pontoppidan, M. “Development of a Combustion Process for a High Performance 2-Stroke Engine with High Pressure Direct Injection,” SAE Technical Paper 2004-01-2942 2004
- Basshuysen, R. “Ottomotor mit Direkteinspritzung” ATZ/MTZ-Fachbuch Vieweg Germany 2007
- Winkler, F. “Untersuchungen zur Reduktion von Spülverlusten bei kleinvolumigen Zweitaktmotoren” PhD thesis Graz University of Technology 2009
- Johnson, J. Braven, K.R.D. “Comparison of Homogeneous, Stratified and High-Squish Stratified Combustion in a Direct-Injected Two-Stroke Engine,” SAE Technical Paper 2008-32-0030 2008 10.4271/2008-32-0030
- Harker, N. DenBraven, K.R. Johnson, J. Findlay, A. “University of Idaho's Clean Snowmobile Design Using a Direct-Injection Two-Stroke Engine,” SAE Technical Paper 2008-32-0031 2008 10.4271/2008-32-0031
- ANSYS Fluent “Gambit User's Guide” Fluent Inc 2005
- ANSYS Fluent “Fluent 6.3 User's Guide” Fluent Inc 2005
- ANSYS Fluent “UDF Manual” Fluent Inc 2005
- Petermeier, L. “Simulation der Gemischbildung wandgeführter Otto - DE Brennverfahren unter besonderer Berücksichtigung der Strahl-Wandinteraktion” TU Graz 2001
- Eichlseder, H. Klüting, M. Piok, W.F. “Grundlagen und Technologien des Ottomotors” Springer 2008
- Stanciu, A.S. “Gekoppelter Einsatz von Verfahren zur Berechnung von Einspritzhydraulik, Gemischbildung und Verbrennung von Ottomotoren mit Kraftstoff-Direkteinspritzung” TU Berlin 2005
- Trattner, A. “Experimentelle Untersuchungen und thermodynamische Analyse eines Brennverfahrenskonzepts für 4-Takt Hochleistungsmotoren mit Direkteinspritzung” Graz University of Technology 2009
- Schmidt, S. Schoegl, O. Rothbauer, R.J. Eichlseder, H. et al. “An Integrated 3D CFD Simulation Methodology for the Optimization of the Mixture Preparation of 2-Stroke DI Engines,” SAE Technical Paper 2007-32-0029 2007
- Merker, G. Schwarz, C Stiesch, G. Otto, F. “Verbrennungsmotoren, Simulation der Verbrennung und Schadstoffbildung” B. G Teubner Verlag 10 3-8351-0080-7 2006