This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
The Effects of Injection Timing and Piston Bowl Shape on PHCCI Combustion with Split injections
Technical Paper
2010-01-0359
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
To reduce diesel engine emissions, a split injection strategy with PHCCI combustion in a diesel engine was investigated with simulation. A multidimensional CFD application, Star-CD coupled with a modified 2-D flamelet was used to simulate multiple injection combustion. Several mass ratios of the first injection and second injection conditions compared to the conventional pilot and main injection strategy were evaluated. The injection angle and the injection timing of the first injection were fixed to 150° and 55° BTDC, respectively. Because of the early injection, the in-cylinder pressure and temperature were much lower than those of normal injection conditions, and the fuel could not fully evaporate. As a result, wall impingement can be occurred, and THC and CO would be increased. To eliminate the wall impingement, the injection timing of the first injection was then retarded to 35-30° BTDC, and the piston bowl geometry was modified to capture droplets in the piston bowl. Subsequently, NOx and soot were reduced substantially. Finally, the piston bowl shape was modified again for spray re-entrance. In these results, NOx and soot were significantly reduced in all split conditions. The modified piston bowl shape was produced and validated in the engine experiment.
Authors
Topic
Citation
Lee, S., Choi, H., and Chung, J., "The Effects of Injection Timing and Piston Bowl Shape on PHCCI Combustion with Split injections," SAE Technical Paper 2010-01-0359, 2010, https://doi.org/10.4271/2010-01-0359.Also In
References
- Najt, P. Foster, D.E. “Compression-ignited Homogeneous Charge Combustion,” SAE Technical Paper 830264 1983
- Thring, R.H. “Homogeneous-Charge Compression Ignition (HCCI) Engines,” SAE Technical Paper 892068 1989
- Stanglmaier, R.H. Roberts, C.E. “Homogeneous Charge Compression Ignition (HCCI): Benefits, Compromises, and Future Engine Application,” SAE Technical Paper 1999-01-3682 1999
- Musculus, M.P.B. Kattke, K. “Entrainment Waves in Diesel Jets,” SAE Int. J. of Engines 2 1 1170 1193 2009
- Yanagihara, H. Sato Y. Mizuta J. A Study of DI diesel combustion under uniform higher-dispersed mixture formation JSAE Review 18 247 254 1997
- Yanagihara, H. Simultaneous Reduction of NOx and soot in diesel engines using a new mixture preparation method JSME International Journal 40 4 1997
- Hasegawa, R. Yanagisawa, H. “HCCI Combustion in DI Diesel Engine,” SAE Technical Paper 2003-01-0745 2003
- Akagawa H. Miyamoto, T. Harada, A. Sasaki, S. Shimazaki, N. Hashizume, T. “Approaches to Solve Problems of the Premixed Lean Diesel Combustion,” SAE Technical Paper 1999-01-0183 1999
- Yokota, H. Kudo, Y. Nakajima, H. Suzuki, T. A New Concept for Low Emission Diesel Combustion,” SAE Technical Paper 970891 1997
- Iwabuchi, Y. Kawai, K. Shoki, T. Takeda, Y. “Trial of New Concept Diesel Combustion System-Premixed Compression-Ignition Combustion,” SAE Technical Paper 1999-01-0185 1999
- Walter, B. Gatellier, B. Development of the High Power NADITM Concept using Dual Mode Diesel Combustion to achieve Zero NOx and Particulate Emissions,” SAE Technical Paper 2002-01-1744 2002
- Su, W. Wang, H. Liu, B. Injection Mode Modulation for HCCI Diesel Combustion,” SAE Technical Paper 2005-01-0117 2005
- Beale, J. Reitz, R. Modeling Spray Atomization with the Kelvin-Helmholtz / Rayleigh-Taylor Hybrid Model Atomization and Spray 9 623 650 1999
- O'Rourke Collective Drop Effects on Vaporizing Liquid Sprays Princeton University 1981
- Poling, B. E. Praustiz, J. M. O'connel, J. P. The Properties of Gases and Liquids Fifth Mcgraw-Hill 2001
- Spalding, D. B. The Combustion of Liquid Fuels, Fourth Symposium (International) on Combustion The Combustion Institute Pittsburge, Penn. 1953
- Patel, A. Kong, S-C. Reitz, R. “Development and Validation of a Reduced Reaction Mechanism for HCCI Engine Simulations,” SAE Technical Paper 2004-01-0558 2004
- Peters, N. Laminar Diffusion Flamelet Models in Non-Premixed Turbulent Combustion Prog. Energy Combust. Sci. 10 319 339 1984
- Hasse, C. Peters, N. A Two Mixture Fraction Flamelet Model Applied to Split Injections in a DI Diesel Engine Thirtieth Symposium (International) on Combustion 2755 2762 2005
- Felsch, C. Gauding, M. Hasse, C. Vogel, S. Peters, N. An extended flamelet model for multiple injections in DI Diesel engines Proc. Combust. Inst. 32 2775 2783 2009
- Lim, J. Choi, S. Lee, K. Lee, J. Min, K. Modeling of Combustion Process of Multiple Injection in HSDI Diesel Engines using Modified Two-Dimensional Flamelet,” SAE Technical Paper 2007-24-0042 2007
- Patel, A. Kong, S. C. Reitz, R. D. “Development and Validation of a Reduced Reaction Mechanism for HCCI Engine Simulations,” SAE Technical Paper 2004-01-0558 2004
- Fucos, A. Knox-Kelecy, A. L. Foster, D. E. Application of a Phenomenological Soot Model to Diesel Engine Combustion COMODOA 94 571 576 1994
- Hewson, J. Pollutant Emissions from Non-premixed Hydrocarbon Flames UC San Diego 1997