This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Improvement of a High-Performance Diesel-Engine by means of Investigation on different Injection Strategies
Technical Paper
2009-24-0008
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
Test bench investigations on a high-performance diesel engine equipped by regulation with an air- restrictor have shown, among other things, that different injection strategies have a remarkable influence on the engine performance and exhaust emissions. A part of these investigations is reported in this paper. In particular the attention here is directed to the following two topics:
-
comparison between two different injector types (solenoid vs. piezo)
-
comparison among different injection timings (only main injection vs. pre-injection).
Looking for a continuous increasing of engine performance a detailed understanding of the injection and combustion processes is mandatory. For this task a fast response 3D-CFD-simulation-tool has been applied to the engine development process. This tool acts as a virtual eye inside the combustion chamber which permits to have a look beyond the test bench. So it was possible to find explanations for the occurring phenomena and then virtually test new approaches to improve the engine performance (virtual engine development). The results show, e.g., that against the expectations the piezo-injector is not overall more performing than the solenoid injector and the setting of a pre-injection under particular circumstances permits to increase the engine performance in the speed range above the choking line of the air restrictor. All the presented investigations take into account the FIA (Fédération Internationale de l'Automobile) general regulations and Volkswagen self-limitation on the smoke emissions for race engines.
Recommended Content
Authors
Topic
Citation
Chiodi, M., Mack, O., Bargende, M., Paule, K. et al., "Improvement of a High-Performance Diesel-Engine by means of Investigation on different Injection Strategies," SAE Technical Paper 2009-24-0008, 2009, https://doi.org/10.4271/2009-24-0008.Also In
References
- Wichelhaus D. “Optimierung der diesel-motorischen Verbrennung für hohe Leistung bei begrenztem Luftangebot” Dissertation Universität Stuttgart expert Verlag 2009
- Hammer J. “Einspritztechnik I + II” Lecture notes Universität Stuttgart 2004
- Robert Bosch GmbH “Dieselmotormanagement” Vieweg Verlag 2004
- N. N. “Star-CD User Manual Version 3.15” Computational Dynamics Ltd. London 2002
- Chiodi M. Berner H.-J. Bargende M. “Investigation on Different Injection Strategies in a Direct-Injected Turbocharged CNG-Engine” SAE Paper 2006-01-3000
- Zuelch C. “Konzepte für einen sicheren Direktstart von Ottomotoren” Dissertation Universität Stuttgart Shaker Verlag 2007
- Zuelch C. Kulzer, A. Chiodi M. Bargende M. “Directstart: Investigation of Mixture Formation by Means of Optical Measurements and 3D-CFD-Simulation” SAE Paper 2005-01-3686
- Bohatsch S. Hofmann B. Ferrari A. Chiodi M. Berner H.-J. Bargende M. “Darstellung verschiedener Betriebsstrategien an einem Erdgasmotor mit innerer Gemischbildung” Tagung Gasfahrzeuge, Haus der Technik, Dresden 2006
- Chiodi M. Berner H.-J. Bargende M. “Investigation on Mixture Formation and Combustion Process in a CNG-Engine by Using a Fast Response 3D-CFD-Simulation” SAE Paper 2004-01-3004
- Chiodi M. Berner H.-J. Bargende M. “Schnelle 3D-CFD-Untersuchungen des Ansaugsystems eines aufgeladenen 1I-Erdgasmotors mit dem Entwicklungstool QuickSim ” Tagung Ansaug-systeme aufgeladener Motoren, Haus der Technik, Ludwigsburg 2006
- Chiodi M. Bargende M. “Improvement of Engine Heat-Transfer Calculation in the Three-Dimensional Simulation Using a Phenomenological Heat-Transfer Model” SAE-Paper 2001-01-3601
- Bargende M. Riegler U. Scholz B. “Der virtuelle Motor - Fiktion oder Realitaet?” Tagung Im Haus der Technik Essen October 2000
- Otto F. Dittrich P. Wirbeleit F. “Status of 3D-Simulation of Diesel Combustion” 3. Internationales Indiziersymposium 1998
- Badami M. Bevilacqua V. Millo F. Chiodi M. Bargende M. “GDI Swirl Injector Spray Simulation: a Combined Phenomenological-CFD Approach” SAE Paper 2004-01-3005
- Zuarini A. Chiodi M. Bargende M. “Numerical Analysis of Combustion Process in Four-Strokes Spark Ignition Engines” Graduation Thesis IVK - Universität Stuttgart 2002
- Grill M. Schimd A. Chiodi M. Berner H.-J. Bargende M. “Calculating the Properties of User-Defined Working Fluids for Real Working-Process Simulations” SAE Paper 2007-01-0936
- Bargende M. “Ein Gleichungsansatz zur Berechnung der instationaeren Wandwaerme-verluste im Hochdruckteil von Ottomotoren” Der Arbeitsprozess des Verbrennungsmotors Graz 1991
- Berner H.-J. Chiodi M. Bargende M. “Cycle Simulation in Consideration of Caloric Properties of the Fuel Natural Gas” Der Arbeitsprozess des Verbrennungsmotors Graz 2003
- Lau M. Chiodi M. Bargende M. “Entwicklung eines neuronalen Netzes zur Berechnung von Zündverzugszeiten für Ottokraftstoffe” Seminar Paper Universität Stuttgart 2005
- Reinhardt S. Chiodi M. Bargende M. “Entwicklung eines neuronalen Netzes zur besseren Berechnung der kalorischen Eigenschaften des Arbeitsmittels in CNG- Motoren” Graduation Thesis IVK - Universität Stuttgart 2002
- Reinhardt H. Schmidt D. Bargende M. “Modeling the Ignition Delay for DI-Diesel-Engines” 2008