This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Combustion System Optimization of a Low Compression-Ratio PCCI Diesel Engine for Light-Duty Application
Journal Article
2009-01-1464
ISSN: 1946-3936, e-ISSN: 1946-3944
Sector:
Topic:
Citation:
Catania, A., d’Ambrosio, S., Finesso, R., Spessa, E. et al., "Combustion System Optimization of a Low Compression-Ratio PCCI Diesel Engine for Light-Duty Application," SAE Int. J. Engines 2(1):1314-1326, 2009, https://doi.org/10.4271/2009-01-1464.
Language:
English
References
- Iwabuchi Y. Kawai K. Shoji T. Takeda Y. “Trial of New Concept Diesel Combustion System – Premixed Compression-Ignited Combustion,” SAE Paper 1999-01-0185 1999
- Kidoguchi Y. et al. “Experimental and Theoretical Optimization of Combustion Chamber and Fuel Distribution for the Low Emission DI Diesel Engine,” ASME Trans., J. Eng. Gas Turbines Power 125 1 351 357 2003
- DeRisi A. Donateo T. Laforgia D. “Optimization of the Combustion Chamber of Direct Injection Diesel Engines,” SAE Paper No. 2003-01-1064 2003
- Hajireza S. Regner G. Christie A. Egert M. Mittermaier H. “Application of CFD Modeling in Combustion Bowl Assessment of Diesel Engines Using DoE Methodology,” SAE Paper No. 2006-01-3330 2006
- Sakata I. Nagae M. Omae K. Ito H. “A New Combustion Concept for Passenger Car Diesel Engines Based on a Low Compression Ratio,” 15th Aachener Kolloquium Fahrzeug und Motorentechnik 2006
- Naber D. Dohle U. Krueger M. Schumacher H. Hondros C. “Cold Start and Cold Run Investigations for Direct Injected Passenger Car Diesel Engines,” 15th Aachener Kolloquium Fahrzeug und Motorentechnik 2006
- Fasolo B. Doisy A. Dupont A Lavoisier F. “Combustion System Optimization of a New 2 Liter Diesel Engine for EURO IV,” SAE Paper No. 2005-01-0652 2005
- Reveille B. Kleemann A. Knop V. Habchi C. “Potential of Narrow Angle Direct Injection Diesel Engines for Clean Combustion: 3D CFD Analysis,” SAE Paper No. 2006-01-1365 2006
- Suzuki M. Tsuzuki N. Teramachi Y. “The New Toyota L-4 Direct-injection Diesel Engine – Toyota D-4D Clean Power Concept,” 26th Internation. Vienna Motor Symposium 2005
- Cooper B. Penny I. Beasley M. Greaney A. Crump J. “Advanced Diesel technology to Achieve Tier2 Bin5 Emissions Compliance in US Light-Duty Diesel Applications,” SAE Paper 2006-01-1145 2006
- Cipolla G. Vassallo A. Catania A.E. Spessa E. Stan C. Drischmann L. “Combined application of CFD modeling and pressure-based combustion diagnostics for the development of a low compression ratio high-performance diesel engine,” 2007 SAE Transactions, Journal of Engines 1521 1539 SAE Paper No. 2007-24-0034 .
- Baratta M. Catania A.E. Ferrari A. Finesso R. Spessa E. “Innovative Multizone Premixed-Diffusion Combustion Model for Performance and Emission Analysis in Conventional and PCCI Diesel Engines,” Proceedings, COMODIA 2008, July 28-31 Sapporo, Japan JSME No. 08-202 351 362 Paper No. HC4-3
- Dec J.D. “A conceptual Model of Diesel Combustion Based on Laser-Sheet Imaging” SAE Paper No. 970873 1997
- Egnell R. “A Simple Approach to Studying the Relation between Fuel Rate, Heat Release Rate and NO Formation in Diesel Engines,” SAE Paper No. 1999-01-3548 1999
- Egnell R. “The Influence of EGR on Heat Release Rate and NO Formation in a DI Diesel Engine” SAE Paper No. 2000-01-1807 2000
- Egnell R. “Combustion Diagnostics by Means of Multizone Heat Release Analysis and NO Calculation” SAE Paper No. 981424 1998
- Sastry G.V.J. Chandra H. “A Three-Zone Heat Release Model for DI Diesel Engines” SAE Paper No. 940671 1994