This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Wear of Friction Material during Vehicle Braking
Technical Paper
2009-01-1032
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
An analysis of the vehicle braking, combining with the linear relation between wear and frictional work already investigated, was used to establish a wear equation. Initial braking velocity, the number of brakings per 1 km and pad thickness loss per 1000 km were determined by using taxis with identical car types and identical pad qualities. Based on the averaged experimental results and some normal braking conditions, the calculated average apparent specific wear rate through the equation was unexpectedly found to decrease firstly and then increase with the increase of average initial braking velocity. The pad friction properties relevant to the equation analysis were tested by using a dynamometer, followed by measuring wear as a function of temperature at three different initial velocities that equal the average initial braking velocities respectively. The measurement showed that wear was approximately proportional to initial velocity squared at the temperature of 50 to 300 °C, in good agreement with the equation. The estimated vehicle braking temperatures by comparing two different types of wear are close to the previously reported ones.
Recommended Content
Technical Paper | Lining Life Prediction Based on Rotor 1-D Thermal Model and Applicability of Wear versus Temperature Data |
Technical Paper | Pad Wear Simulation Model |
Technical Paper | Prediction of Brake Pad Life-Further Development of LWH |
Authors
Topic
Citation
Zhang, S., Chen, W., and Li, Y., "Wear of Friction Material during Vehicle Braking," SAE Technical Paper 2009-01-1032, 2009, https://doi.org/10.4271/2009-01-1032.Also In
References
- Cueva G. Sinatora A. Guesser W.L. Tschiptschin A.P. 2003 Wear Resistance of Cast Irons Used in Brake Disc Rotors Wear 255
- Todorovi J. Duboka. Arseni Ž. 1995 Operational Life Expectancy of Rubbing Elements in Automotive Brakes Tribology International 28 (7)
- Mackin Thomas J. Noe Steven C. Ball K.J. et al. 2002 Thermal Cracking in Disc Brakes Engineering Failure Analysis 9
- Pauwelussen J.P. Gootjes L. Schröder C. Köhne K.-U. Jansen S. Schmeitz A. 2003 Full Vehicle ABS Braking Using the SWIFT Rigid Ring Tyre Model Control Engineering Practice 11
- Segal L. 1999 Diagnostic Method for Vehicle Brakes NDT & E International 32
- Czichos H. Klaffke D. Santner E. Woydt M. 1995 Advances in Tribology: the Materials Point of View Wear 190
- Shaoyang, Zhang FuPing Wang 2007 Comparison of Friction and Wear Performances of Brake Material Dry Sliding against Two Aluminum Matrix Composites Reinforced with Different SiC Particles Journal Materials Processing Technology 182
- Shaoyang Zhang FuPing Wang 2007 Comparison of Friction and Wear Performances of Brake Materials Containing Different Amounts of ZrSiO 4 Dry Sliding against SiC P Reinforced Al Matrix Composites Materials Science Engineering A 443
- Gopal P. Dharani L.R. Blum Frank D. 1995 Load, Speed and Temperature Sensitivities of a Carbon-fiber-reinforced Phenolic Friction Material Wear 181 183
- Rhee S.K. Jacko M.G. Tsang P.H.S. 1991 The Role of Friction Film in Friction, Wear and Noise of Automotive Brakes Wear 146
- Rhee S.K. Jacko M.G. Tsang P.H.S. 1985 Comparison of Chase and Inertial Brake Dynamometer Testing of Automotive Friction Materials Wear 103
- Gopal P. Dharani L.R. Blum Frank D. 1994 Fade and Wear Characteristics of a Glass-fiber-reinforced Phenolic Friction Material Wear 174
- Blau Peter J. 2001 The Significance and Use of the Friction Coefficient Tribology International 34
- Jiang Jun Ulbrich Heinz 2001 Derivation Coefficient of Friction at High Sliding Speeds from Energy Conservation over the Frictional Interface Wear 247
- Brake Linings for Road Vehicles: Development and Testing Verlag Moderne Industrie AG & Co. 1991 60 63
- Straffelini G. Pellizzari M. Molinari A. 2004 Influence of Load and Temperature on the Dry Sliding Behaviour of Al-based Metal-matrix-composites against Friction Material Wear 256