This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Drag Force Reduction of a Bluff-Body with an Underbody Slant and Rear Flaps
Journal Article
2008-01-2599
ISSN: 1946-391X, e-ISSN: 1946-3928
Sector:
Topic:
Citation:
Kowata, S., Ha, J., Yoshioka, S., Kato, T. et al., "Drag Force Reduction of a Bluff-Body with an Underbody Slant and Rear Flaps," SAE Int. J. Commer. Veh. 1(1):230-236, 2009, https://doi.org/10.4271/2008-01-2599.
Language:
English
References
- Norem, H. Saetran, L. Thordarson, S. “Measures to Reduce the Generation of ‘Snow Smoke’ Behind Heavy Vehicles,” Proceedings of the PIARC 2002 XI International Winter Road Congress Sapporo, Japan 2002
- Wood, R.M. Bauer, S.X.S. “Simple and Low-Cost Aerodynamic Drag Reduction Devices for Tractor-Trailer Trucks,” SAE TP 2003-01-3377 2003
- Bayraktar, I. Landman, D. Cary W.K. III Wood, R.M. Flamm, J. Hunter, C. “An Assessment of Drag Reduction Devices for Heavy Trucks Using Design of Experiments and Computational Fluid Dynamics,” SAE TP 2005-01-3526 2005
- Ortega, J.M. Salari, K. “An Experimental Study of Drag Reduction Devices for a Trailer Underbody and Base,” Proceedings of the 34th AIAA Fluid Dynamics Conference and Exhibit , AIAA-2004-2252 Portland, Oregon 2004
- Khalighi, B. Zhang, S. Koromilas, C. Balkanyi, S.R. Bernal, L.P. Laccarino, G. Moin, P. “Experimental and computational study of unsteady wake flow behind a bluff body with a drag reduction device,” SAE TP 2001-01-1042 2001
- Cary W.K. III Landman, D. Wood, R.M. “Experimental Investigation of Wake Boards for Drag Reduction on an Ahmed Body,” SAE TP 2006-01-3530 2006
- Browand, F. Radovich, C. Boivin, M. “Fuel Savings by Means of Flaps Attached to the Base of a Trailer: Field Test Results,” SAE TP 2005-01-1016 2005
- Kim, M. “Aerodynamic Simulation on the Drag Reduction Device of a Large-Sized Bus Model,” International Journal of Heavy Vehicle Systems 12 3 207 224 2005
- Song, J. “Control of Passenger Vehicle's Aerodynamic Characteristics by Varying Rear Configuration,” Ph. D. Dissertation (Engineering) of Tohoku University Sendai, Japan 2006
- Ruhrmann, A. Zhang, X. “Influence of Diffuser Angle on a Bluff Body in Ground Effect,” Transactions of the ASME 125 332 338 2003
- Ahmed, S.R. Ramm, G. Faltin, G. “Some Salient Features of the Time-Averaged Ground Vehicle Wake,” SAE TP 840300 1984
- Sumitani, K. Maeda, K. Ichinose K. “Development of Vehicle Fluid dynamics : Flow around the Vehicle and Aerodynamic Characteristics,” Journal of Japan Society of Fluid Mechanics 23 6 445 454 2004
- Nouzawa T. “Wake Structure of a Notchback Model with Critical Geometry,” Transactions of the Japan Society of Mechanical Engineers. B 60 575 2365 2370 1994
- Coleman, H.W. Steele, W.G. “Engineering application of experimental uncertainty analysis,” AIAA Journal 33 10 1888 1896 1995
- Kuroishi, S. Nakatani, H. “The analysis of the flow of the near rear base of the car,” Transactions of the Journal of Society of Automotive Engineers of Japan 22 1 1991
- Cooper, K.R. Bertenyi, T. Dutil, G. Syms, J. Sovran, G. “The aerodynamic performance of automotive underbody diffusers,” SAE TP 980030 1998
- Cooper, K.R. Sovran, G. Syms, J. “Selecting automotive diffusers to maximize underbody downforce,” SAE TP 2000-01-0354 2000
- Ha, J. Kim, T. Yun, S. Ku, Y. Lee, D. “Design of Experiments and Uncertainty Analysis for the Reliability Guarantee of Wake Flow Characteristics behind a Square Cylinder,” Journal of the Wind Engineering Institute of Korea 11 1 89 96 2007