This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Aerodynamic Design Improvement of NDSU Solar Car through Computational Fluid Dynamics
Technical Paper
2008-01-2251
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
In the design of solar powered cars aerodynamic efficiency is extremely important. Due to the limited power and energy sources available, the aerodynamic design of the car must provide a low coefficient of drag. In order to identify the major drag source areas in the design and to improve the aerodynamics performance of the current NDSU solar car an extensive computational fluid dynamics (CFD) study was performed using ANSYS CFX 10.0. The study was set into two paths. The first path focused on modifying the current NDSU solar car design in order to reduce the drag force. The second path was to design a completely new solar car with better aerodynamics performance. Through the CFD analysis of all the designs considered major drag source areas were identified as the underbody, the dome, and the nose section of the car. In order to reduce the drag contribution from the underbody the inclusion of fairings enclosing wheels, suspension, brake, and motor components was recommended for all designs. Even though fairings increase the cross sectional area, their overall effect greatly reduced the drag force. It was found through CFD analysis that the individual fairings can decrease the drag force created by the wheels, suspension, brake, and motor components by 50%. Simulations indicated that the nose section of the current solar car had the largest contribution to the drag force. Therefore reducing the drag on the nose was essential in order to increase the efficiency of the car. The nose section was modified to a leaner, pointed, and gradually angled shape. The separated flow region behind the dome in the current car design was eliminated and the aerodynamic characteristics of the dome section were improved by designing a streamlined and low profile dome shape. In all designs the limitations and regulations set forth by the American Solar Car Challenge (ASC) were followed. The results of the analysis for the current NDSU solar car showed that with basic modifications the coefficient of drag could be reduced by approximately 5%. From the analysis of new concept cars a few major recommendations were concluded. The best aerodynamic performance was obtained for a design with three wheels with individual fairings on each wheel, a thin nose section, and a lean a streamlined canopy section. The paper includes details of the computational analysis including the comparison of different designs.
Recommended Content
Technical Paper | The Aerodynamics Development of the New Nissan Qashqai |
Technical Paper | A Calibration Study of CFD for Automotive Shapes and CD |
Journal Article | Investigation of Wheel Ventilation-Drag using a Modular Wheel Design Concept |
Authors
Topic
Citation
Hoerl, A., Larson, D., Stenson, M., Dennis, K. et al., "Aerodynamic Design Improvement of NDSU Solar Car through Computational Fluid Dynamics," SAE Technical Paper 2008-01-2251, 2008, https://doi.org/10.4271/2008-01-2251.Also In
References
- American Solar Car Challenge (AMC) “History, Results, Rules and Regulations.” AMC Online. 6 February 2005 August - December 2006 http://www.americansolarchallenge.org/
- Anderson John David Fundamentals of Aerodynamics Boston McGraw-Hill 2001
- ANSYS Products “ANSYS CFX Testimonials.” 2005 ANSYS Inc August - December 2006 http://www.ANSYS.com/products/cfx.asp
- Incropera Frank P. DeWitt David P. “Fundamentals of Heat and Mass Transfer,” John Wiley & Sons 5 th 2002
- Koike Masaru Nagayoshi Tsunehisa Hamamoto Naoki Research on Aerodynamic Drag Reduction by Vortex Generators Mitsubishi Motors 2004
- Kwasnoski John Murphy Richard “Determining the aerodynamic drag coefficient of an automobile” Department of Physics, Western New England College 29 June 1984
- Munson B.R. Young D.F. Okiishi T.H. “Fundamentals of Fluid Mechanics,” John Wiley & Sons 4 th 2002
- Muyl Frederique Dumas Laurent Herbert Vincent Hybrid method for Aerodynamic Shape Optimization in Automotive Industry Paris, France University Pierre at Marie Curie
- White Frank M. “Fluid Mechanics,” McGraw-Hill 4 th 1999