This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Electrical Impedance Analysis of Vehicle Structural Components and Assemblies
Technical Paper
2008-01-1474
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
The objective of this paper is to propose that the automotive engineering “legacy” approach of assuming that vehicle electrical return paths using conductive structural components have zero (0) ohms of impedance, needs to be reviewed. The process in this review consists of the development of an equivalent circuit composed of both real (“resistive”) and reactive elements (due to inductance and capacitance). This issue needs to be addressed due to the increased complexity of electrical and electronics systems in vehicles and the use of the vehicle structural (such as chassis, frame, or bracket) components to provide a path for the return of electrical power and/or signals as a way to eliminate additional wiring manufacturing issues, cost, and weight contribution to a vehicle. The effects of both real and reactive impedances in the return path can lead to “ground shift” conditions, data signal corruption, and/or electromagnetic compatibility (EMC) conditions that may impact the performance of the vehicle systems or the ability to meet vehicle level EMC requirements. The methods used to illustrate these issues include evaluation of the geometric shapes of representative component assemblies, the material properties (including electrical characteristics), the conductivity of interface surfaces, and the resulting current path topology. The data that is shown consists of representative mechanical assembly details, equivalent reactive component values, and their circuit representation. Additional information is presented regarding the effectiveness of various techniques that have been used for vehicle EMC compliance, such as the application of “ground straps”, and/or requirements for electrical bonds. Next steps in this work are proposed as electrical impedance measurements of representative on-vehicle structural elements and then these values would be compared with data developed from analysis and modeling work. It is anticipated that additional work can then accomplished to develop guidelines for use of structural components as electrical connections or portions of electrical paths.
Recommended Content
Technical Paper | Impact of Lightning Strikes on Nuclear Power Generating Stations |
Technical Paper | Zero Resistance Technology (ZRT) |
Technical Paper | EMI EFFECTS IN ELECTRO-ELECTRONIC EQUIPMENTS/SYSTEMS OF AIRCRAFT |
Authors
Citation
Steffka, M., Goodwin, W., Jha, S., and Denny, H., "Electrical Impedance Analysis of Vehicle Structural Components and Assemblies," SAE Technical Paper 2008-01-1474, 2008, https://doi.org/10.4271/2008-01-1474.Also In
References
- Fitzsimmons J.T. Ignition Requirements for High-Compression Engines
- Steffka M. “Conducted Emissions” 2007 IEEE International Symposium on EMC EMC Global University session
- Ott H. Noise Reduction Techniques in Electronic Systems Second Wiley 1988
- Paul C. Introduction to Electromagnetic Compatibility Second Wiley-Interscience 2006
- Denny H. Grounding for the Control of EMI First Don White Consultants, Inc. Gainesville, Virginia 1983
- Baertlein B. Liao W. Gilmore W. The role of grounding in automotive EMC IEEE International EMC Symposium 1999
- Reference Data for Radio Engineers Howard W. Sams & Co., Inc. Sixth 1977
- Ott H. “Digital Circuit Grounding and Interconnection” IEEE International EMC Symposium 1981
- Steffka M. Trzcinski D. “Engine Component Effects on Spark Ignition Caused Radio Frequency Interference (RFI)” 2007 SAE Congress
- Denny H. “Grounding – More Than A Connection To Earth” INCEMIC
- Denny H. “Some RF Characteristics of Bonding Systems” IEEE Transactions on Electromagnetic Compatibility EMC-11 1 February 1969
- “Grounding, Bonding, and Shielding for Electronics Equipments and Facilities” MIL-HBK-419A 1987
- Dorf R.C. “The Electrical Engineering Handbook” Second CRC Press LLC Salem, MA
- Otoshi T. Cirillo R. Sosnowski “ Measurements of Complex Dielectric Constants of Paints and Primers for DSN Antennas: Part I ” TMO Progress Report 1999
- Military Specification, Bonding, Electrical, and Lightning Protection for Aerospace Systems MIL-B-5087B(ASG) 1964