This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Modeling of Combustion Process of Multiple Injection in HSDI Diesel Engines using Modified Two-Dimensional Flamelet
Technical Paper
2007-24-0042
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
Ignition delay of the second injection of HSDI diesel engines is generally much shorter than that of the first injection because of the interaction between the radicals generated during the combustion process and the mixed gas of the second injection. Although previous Diesel combustion models could not explain this reaction, Hasse and Peters described the mass and heat transfer of the second injection and estimated the ignition delay of the second injection using two-dimensional flamelet equations. But a simulation of the two-dimensional flamelet equations requires enormous computational time. Thus, to analyze the combustion phenomena of the multiple injection mode in HSDI diesel engines effectively, the two-dimensional flamelet combustion model was modified in this study. To reduce the calculation time, two-dimensional flamelet equations were only applied near the stoichiometric region. If this region was ignited, species and temperatures of other regions were changed to the steady-state solutions of one dimensional flamelet equations. By this method the calculation time for solving flamelet equations was reduced by 80 percent without any loss of calculation accuracy.
A new modified 2-D flamelet combustion model was coupled to commercial CFD code by using user subroutines. At first, to verify this combustion model, autoignition and combustion processes were investigated in a pre-combusted vessel. The simulation results of ignition delay of the second injection were well matched with the experimental results. Secondly, simulation of combustion process and emissions for multiple injections was performed, and verified by the experiment. The pressure simulated by the CFD code well matched with the experimental data. If the mixture of the second injection came in contact with the radicals originated by the first injection immediately, oxygen was consumed immediately due to short ignition delay and this oxygen consumption will generate a lot of soot. Thus the injection timing and amount of the first and second injection should be considered carefully. As a result, the combustion model used in this study can be applied in the design stage of an engine using multiple injections.
Recommended Content
| Technical Paper | Modeling Radiant Heat Loss Characteristics in a Diesel Engine |
| Technical Paper | Improvements of the KIVA Dense Spray Modeling for HSDI Diesel Engines |
| Technical Paper | CFD Simulation of Diesel Injection and Combustion |
Authors
- Jaeman Lim - School of Mechanical and Aerospace Engineering, Seoul National University, Korea
- Seungmok Choi - School of Mechanical and Aerospace Engineering, Seoul National University, Korea
- Kyeung-hyeon Lee - School of Mechanical and Aerospace Engineering, Seoul National University, Korea
- Kyoungdoug Min - School of Mechanical and Aerospace Engineering, Seoul National University, Korea
- Jonghwa Lee - School of Mechanical Engineering, Ajou University, Korea
Topic
Citation
Lim, J., Choi, S., Lee, K., Min, K. et al., "Modeling of Combustion Process of Multiple Injection in HSDI Diesel Engines using Modified Two-Dimensional Flamelet," SAE Technical Paper 2007-24-0042, 2007, https://doi.org/10.4271/2007-24-0042.Also In
References
- Wang T.C. Han J.S. Xie X. Lai M. C. Henein Naeim A. Schwarz Ernest Bryzik Walter B “Direct Visualization of High Pressure Diesel Spray and Engine Combustion” SAE Paper 1999-01-3496
- Lapuerta M. Armas O. Hernandez J. J. “Effect of the Injection Parameters of a Common Rail Injection System on Diesel Combustion Through Thermodynamic Diagnosis” SAE Paper 1999-01-0194
- Henein N.A. Singh I.P. Zhong L. Lai M-C. Bryzik W. “New Integrated “O.P.E.R.A.S.” Strategies for Low Emissions in HSDI Diesel Engines” SAE Paper 2003-01-0261
- Spalding D. B. “Mixing and Chemical Reaction in Steady Confined Turbulent Flames” Thirteen Symposium (International) on Combustion 649 657 1971
- Magnussen B. F. Hjertager B. H. “On Mathmatical Models of Turbulent Combustion with Special Emphasis on Soot Formation and Combustion” Sixteenth Symposium (International) on Combustion 719 729 1977
- Reitz R. D. Rutland C. J. “Development and Testing of Diesel Engine CFD Models” Prog. Energy Combust. Sci 21 173 196 1995
- Kong S. C. Marriott C. D. Reitz R. D. Christensen M. “Modeling and Experiments of HCCI Engine Combustion Using Detailed Chemical Kinetics with Multidimensional CFD” SAE Paper 2001-01-1026
- Peters N. “Laminar Diffusion Flamelet Models in Non-Premixed Turbulent Combustion” Prog. Energy Combust. Sci 10 319 339 1984
- Kuznetsov V. R. “Effect of Turbulence on the Formation of Large Superequilibrium Concentration of Atoms and Free Radicals in Diffusion Flames” Mehan. Zhidkosti Gasa 6 3 9
- Hergart C. A. Barths H. Peters N. “Modeling the Combustion in a Small-bore Diesel Engine Using a Method Based on Representative Interactive Flamelets” SAE Paper 1999-01-3550
- Weber J. Peters N. Bockhorn H. Pittermann R. “Numerical Simulation of the Evolution of the Soot Particle Size Distribution in a DI Diesel Engine Using an Emulsified Fuel of Diesel-water” SAE Paper 2004-01-1840
- Hasse C. Peters N. “A Two Mixture Fraction Flamelet Model Applied to Split Injections in a DI Diesel Engine” Thirtieth Symposium (International) on Combustion 2755 2762 2005
- Beale J. Reitz R. D. “Modeling Spray Atomization with the Kelvin-Helmholtz/Rayleigh-Taylor Hybrid Model” Atomization and Spray 9 623 650 1999
- O'Rourke P. J. “Collective Drop Effects on Vaporizing Liquid Sprays,” Ph. D Thesis Princeton University 1981
- Poling B. E. Praustiz J. M. O'connel J. P. “The Properties of Gases and Liquids : Fifth Edition” Mcgraw-Hill 2001
- Spalding D. B. “The Combustion of Liquid Fuels” Fourth Symposium (International) on Combustion The Combustion Institute Pittsburge, Penn 1953
- El Wakil M.M. Ueyhara O.A. Myers P.S. “A theoretical investigation of the heating-up period of injected fuel droplets vaporizing in air” NACA Technical Note 3179 1954
- Patel A. Kong S. C. Reitz R. D. “Development and Validation of a Reduced Reaction Mechanism for HCCI Engine Simulations” SAE Paper 2004-01-0558 2004
- Hasse C. W. “A Two-Dimensional Flamelet Model for Multiple Injections in Diesel Engines” Ph.D Thesis, RWTH Aachen 2004
- Lim J. Min K. Combustion and Flame, in progress
- Tao F. Golovitchev V., I. Chomiak J. “Application of Complex Chemistry to Investigate the Combustion Zone Structure of DI Diesel Sprays under Engine-Like Conditions” The Fifth International Symposium on Diagnostics and Modeling of Combustion in Internal Combustion Engines (COMODIA 2001) 92 100 2001
- Hewson J. “Pollutant Emissions from Nonpremixed Hydrocarbon Flames” PhD thesis UC San Diego 1997
- Hergart C. Barths H. Peters N. “Modeling the Combustion in a Small-Bore Diesel Engine Using a Method Based on Representative Interactive Flamelets” SAE Paper 1999-01-3550