This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Influence of Nozzle Geometry on Spray Characteristics in Non-evaporative and Evaporative Conditions
Technical Paper
2007-24-0023
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
An experimental study of real multi-hole diesel nozzles with different geometry in terms of conicity factor has been performed under current DI Diesel engines operating conditions.
A complete characterization of the internal nozzle flow and the sprays injected under non-evaporative conditions has been performed. The results of that study are applied in order to assist the analysis of spray in evaporative conditions. In this case, results of liquid-phase fuel penetration were obtained from a wide optical access engine operating under non-reacting conditions.
From these measurements, a comparison of the results with a theoretical Diesel spray model in evaporative conditions has been carried out. This comparison has allowed the determination of the dependence of stabilized liquid length on injection pressure, ambient conditions and nozzle geometry.
Recommended Content
Authors
Citation
Payri, F., Payri, R., Salvador, F., and Gimeno, J., "Influence of Nozzle Geometry on Spray Characteristics in Non-evaporative and Evaporative Conditions," SAE Technical Paper 2007-24-0023, 2007, https://doi.org/10.4271/2007-24-0023.Also In
References
- Hiroyasu H. Arai M. “Structures of fuel sprays in Diesel engines” SAE Paper 900475 1990
- Payri F. Bermúdez V. Payri R. Salvador F. J. “The influence of cavitation on the internal flow and the spray characteristics in Diesel injection nozzles” Fuel 83 419 31 2004
- Kent J. C. Brown G. M. “Nozzle exit flow characteristics for square-edged and rounded inlet geometries” Combust. Sci. Technol. 30 121 132 1983
- Kampmann S. Dittus B. Mattes P. Kirner M. “The influence of hydro grinding at VCO nozzles on the mixture preparation in a DI Diesel engine” SAE Paper 960867 1996
- Soteriou C. Andrews R. J. Smith M. “Direct injection Diesel sprays and the effect of cavitation and hydraulic flip on atomisation” SAE Paper 950080 1995
- Schmidt D. P. Corradini M. L. “The internal flow of Diesel fuel injector nozzles: a review” , Int. J Engine Research 2 1 22 2001
- Ganipa L. C. Andersson S. Chomiak J. “Combustion characteristics of Diesel sprays from equivalent nozzles with sharp and rounded inlet geometries” Combust. Sci. and Tech. 175 1015 1032 2003
- Badock C. Wirth R. Tropea C. “The influence of hydro-grinding on cavitation inside a Diesel injection nozzle on primary break-up under unsteady pressure conditions” Annual conference on liquid atomization & spray systems, Toulouse, France 1999
- Ohrn T. R. Senser D. W. Lefèbvre A. H. “Geometrical effects on discharge coefficients for plain-orifice atomizers” Atomization Spray 1 137 153 1991
- Macián V. Payri R. Margot X. Salvador F. J. “A CFD analysis of the influence of Diesel nozzle geometry on the inception of cavitation” Atomization Spray 13 579 604 2003
- Payri R. García J. M. Salvador F. J. Gimeno J. “Using spray momentum flux measurements to understand the influence of Diesel nozzle geometry on spray characteristics” Fuel 84 551 561 2005
- Argueyrolles B. Marcer R. Le Cottier P. Chaves H. Habchi C. Barbeau B. “A validated numerical simulation of Diesel injector flow using a Vof method” SAE Paper 2000-01-2932 2000
- Goney K. H. Corradini M. L. “Isolated effects of ambient pressure, nozzle cavitation and hole inlet geometry on Diesel injection spray characteristics” SAE Paper 2000-01-2043 2000
- Macián V. Bermúdez V. Payri R. Gimeno J. “New technique for determination of internal geometry of a Diesel nozzles with the use of silicone methodology” Exp. Techniques; 27 39 43 2003
- Desantes J.M. Payri R. Salvador F.J. Gil A. “Development and validation of a theoretical model for Diesel spray penetration” Fuel 85 910 917 2006
- Bemúdez V. García J.M. Juliá E. Martínez S. “Engine with Optically Accessible Cylinder Head: a research tool for injection and combustion processes” SAE Paper 2003-01-1110
- Siebers D. L. “Scaling liquid-phase fuel penetration in diesel sprays based on mixing-limited vaporization” Transaction of the SAE 108 703 728 1999
- Flaig U. Polach W. Zieglet G. “Common rail system (CR-System) for passenger car DI Diesel engines; Experiences with applications for series productions projects” SAE Paper 1999-01-0191 1999
- Favennec A.G. Fruman D.H. “Effect of the needle position on the cavitation of Diesel injectors” Proceedings of the 3 rd ASME/JSME Joint Fluids engineering conference”, Juli 18-23, San Francisco, California 1999
- Bosch W. “The fuel rate indicator: a new measuring instrument for display of the characteristics of individual injection” SAE Paper 660749 1966
- Pastor J. V. Arrègle J. García J. M. Zapata L. D. “Segmentation of Diesel spray images with log-likelihood ratio test algorithm for non-Gaussian distributions” Applied Optics 46 6 888 899 2007
- Naber J.D. Siebers D.L. “Effect of gas density and vaporization on penetration and dispersion of diesel sprays” SAE Paper 960034 1996
- Lichtarowicz A. K. Duggins R. K. Markland E. “Discharge coefficients for incompressible non-cavitating flow through long orifices” J Mech Engng Sci 7 2 210 219
- Payri R. Salvador F. J. Gimeno J. Soare V. “Determination of Diesel sprays characteristics in real engine in-cylinder air density and pressure conditions” J. Mech. Sci. Technol. 19 2040 2052 2005
- Desantes J. M. Payri R. García J. M. Salvador F. J. “A contribution to the understanding of isothermal Diesel spray dynamics” Fuel 86 1093 1101 2007
- Desantes J. M. Arrègle J. López J. J. Cronhjort A. “Scaling laws for free turbulent gas jets and Diesel-like sprays” Atomization and Sprays 16 443 474 2006
- Desantes J.M. Pastor J.V. Payri R. Pator J.M. “Experimental characterization of internal nozzle flow and diesel spray behaviour. Part II. Evaporative onditions.” Atomization and Sprays 15 517 543 2005