This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Characterization of a Catalytic Converter Internal Flow
Technical Paper
2007-01-4024
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
This paper includes a numerical and experimental study of fluid flow in automotive catalytic converters. The numerical work involves using computational fluid dynamics (CFD) to perform three-dimensional calculations of turbulent flow in an inlet pipe, inlet cone, catalyst substrate (porous medium), outlet cone, and outlet pipe. The experimental work includes using hot-wire anemometry to measure the velocity profile at the outlet of the catalyst substrate, and pressure drop measurements across the system. Very often, the designer may have to resort to offset inlet and outlet cones, or angled inlet pipes due to space limitations. Hence, it is very difficult to achieve a good flow distribution at the inlet cross section of the catalyst substrate. Therefore, it is important to study the effect of the geometry of the catalytic converter on flow uniformity in the substrate. The analysis involved determining back pressure (BP) across the converter system for different monolith cell densities, mass flow rates, converter aspect ratio, inlet cone angle, and inlet pipe offset. The numerical results were used to study the velocity profile at the inlet to the substrate, and were verified with experimental measurements of velocity and BP.
Recommended Content
Authors
Citation
Ramadan, B., Lundberg, P., and Richmond, R., "Characterization of a Catalytic Converter Internal Flow," SAE Technical Paper 2007-01-4024, 2007, https://doi.org/10.4271/2007-01-4024.Also In
References
- Lai, M.C. et al. “Three-Dimensional Simulations of Automotive Catalytic Converter Internal Flow” SAE paper 910200 1991
- Will, N.S. Bennett, C.J. “Flow Maldistributions in Automotive Converter Canisters and Their Effect on Emission Control” SAE paper 922339 1992
- Howitt, J.S. Sekella, T.C. “Flow Effects in Monolithic automotive Catalytic Converters” SAE paper 740244 1974
- Wendland, D.W. Matthes, W.R. “Visualization of Automotive Catalytic Converter Internal Flows” SAE paper 861554 1986
- Wendland, D.W. Matthes, W.R. “Effect of Head Truncation on Monolith Converter Emission-Control Performance” SAE paper 922340 1992
- Hwang, K. Lee, K. Mueller, J. Stuecken, T. Schock, H. Lee, J-C. “Dynamic Flow Study in a Catalytic Converter Using LDV and High Speed Flow Visualization” SAE paper 950786 1995
- Lee, S. Bae, C. Lee, Y. Han, T. “Effects of Engine Operating Conditions on Catalytic Converter Temperature in an SI Engine” SAE paper 2002-10-1677 2002
- Cho, Y.S Lee, Y.S. Kim, D.S. Jung, S.Y. Ohm, I.Y. “An Alternative Method for Fast Light-Off of Catalysts - Cranking Exhaust Gas Ignition” SAE paper 2002-01-1678 2002
- Koehlen, C. Holder, E. Vent, G. “Investigation of Post Oxidation and Its Dependency on Engine Combustion and Exhaust Manifold Design” SAE paper 2002-01-0744 2002
- Gregory, D. Read, M. Campbell, B. Inman, G. Nice, G. Hims, R. Rabinowitz, H. Tauster, S. Collin, T. “Emissions Implications of a Twin Close Coupled Catalyst System Designed for Improved Engine Performance on an In-line 4 Cylinder Engine” SAE paper 2001-01-1092 2002
- Onorati, A. Ferrari, G. Derrico, G. “1D Unsteady Flows with Chemical Reactions in the Exhaust Duct-System of SI Engines: Predictions and Experiments” SAE paper 2001-01-0939 2001
- Cundari, M. Nutti, M. “A One-Dimensional Model for Monolithic Converter: Numerical Simulation and Experimental Verification of Conversion and Thermal Responses for Two-Stroke Engine” SAE paper 910668 1991
- Jeong, S.J. Kim, W.S. “Three-Dimensional Numerical Study on the Use of Warm-up Catalyst to Improve Light-Off Performance” SAE paper 2000-01-0207 2000
- Chen, D. Oh, S. Bissett, E. Ostrom, D. “A Three-Dimensional Model for the Analysis of Transient Thermal and Conversion Characteristics of Monolithic Catalytic Converters” SAE paper 880282 1988
- Knon, H. “Close-Coupled Converter Modeling with a Thin-wall Substrate for a Gasoline Engine” SAE paper 2001-01-3806 2001
- Goralski, C. T. Cvhanko, T. B. “Modeling the Effect of Substrate Cell Shape on Conversion in Monolith Catalysts” SAE paper 2001-01-0932 2001
- Ichikawa, S. Takemoto, T. Sumida, H. Koda, Y. Yamamato, K. Shigetsu, M. Komatsu, K. “Development of Low Light-off Three Way Catalyst” SAE paper 1999-01-0307 1999
- Nakajima, H. Yamaguchi, Y. Tashiro, K. Taniguchi, S. Goto, H. “Study of TWC in NOx Adsorber Catalyst System for Gasoline Direct Injection Engine” SAE paper 2001-01-1300 2001
- Ballinger, T. H. Andersen, P. J. “Vehicle Comparison of Advanced Three-Way Catalysts and Hydrocarbon Trap Catalysts” SAE paper 2002-01-0730 2002
- STAR-CD version 3.25 Methodology CD-Adapco Group 2006