This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Investigation of the Effect of Adhesive Coating on the Performance of Threaded Fasteners
Technical Paper
2007-01-1671
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
This study investigates the effect of Teflon and adhesive coatings on the torque-tension relationship and the self-loosening performance of threaded fasteners. Two Teflon insulation coatings and one locking adhesive are considered. The torque-tension relationship is established for coated and uncoated fasteners for both tightening and loosening. Finally, the fasteners are tested to determine their self-loosening performance under cyclic transverse loads. A computer controlled fastener tightening system is used to establish the torque-tension relationship during tightening. The coefficients of thread and bearing friction, and the overall nut factor are measured. The breakaway loosening torque of tightened bolts, along with the coefficients of thread and underhead friction and nut factor are investigated. A modified Junker machine is used to evaluate the self-loosening performance of fasteners with various coatings.
Since the torque-tension relationship and the self-loosening performance of threaded fasteners are highly sensitive to the friction variables, the findings of this study would improve the reliability and safety of bolted assemblies, especially in critical applications.
Recommended Content
| Technical Paper | Torque Angle Signature Analysis of Joints with Thread Rolling Screws and Unthreaded Weld Nuts |
| Ground Vehicle Standard | Steel Stamped Nuts of One Pitch Thread Design - Inch Series |
| Ground Vehicle Standard | Guide for Rivet Selection and Design Consideration |
Authors
Topic
Citation
Ganeshmurthy, S., Housari, B., and Nassar, S., "Investigation of the Effect of Adhesive Coating on the Performance of Threaded Fasteners," SAE Technical Paper 2007-01-1671, 2007, https://doi.org/10.4271/2007-01-1671.Also In
References
- Bickford, J. H. 1997 “An Introduction to the Design and Analysis of Bolted Joints” third Marcel Dekker New York, New York
- Bickford, J. H. Nassar, S. A. 1998 “Handbook of Bolts and Bolted Joints” Marcel Dekker New York, New York
- Juvinall, R. C. Marshek, K. M. 2000 “Fundamental of Machine Component Design” third John Wiley & Sons New York, New York
- Motosh, N. “Development of Design Charts for Bolts Preload up to the Plastic Range” 1976 ASME Journal of Engineering for Industry 849 851
- Shigley, J. E. Mischke, C. R. 1989 “Mechanical Engineering Design” fifth McGraw-Hill New York
- Shoberg, R. “Manual for the T3 Torque-Tension-Friction Testing System” 1990 GSE Inc. Farmington Hills, Michigan, USA
- Nassar, S. A. Barber, G. C. Zuo, D. 2005 “Bearing Friction Torque in Bolted Joints” STLE Tribology Transaction 48 69 75
- Nassar, S. A. Matin, P. H. Barber, G. C. 2005 “Thread Friction Torque in Bolted Joints” Journal of Pressure Vessel Technology November 127 387 393
- Nassar, S. A. El-Khiamy, H. Barber, G. C. Zou, Q. Sun, T. S. “Bearing and Thread Friction in Fasteners,” 2005 Journal of Tribology ASME Transactions 127 263 272
- Hess, D. “Vibration and Shock Induced Loosening: Handbook of Bolts and Bolted Joints,” Bickford, J. H. Nassar, S.A. 1998 Marcel Dekker 911 New York, NY 757 824
- Sakai, T. 1978 “Investigations of Bolt Loosening Mechanisms,” 1st Report: On bolts of transversely loaded joints, Bulletin of JSME 21 1385 1390
- Haviland, G. S. 1983 “Designing With Threaded Fasteners” Mechanical Engineering 105 17 31
- Yamamoto, A. Kasei, S. 1984 “A Solution for the Self-Loosening Mechanism of Threaded Fasteners Under Transverse Vibration,” Bulletin Japan Society of Precision Engineering 18 261 266
- Tanaka, M. Hongo, K. Asaba, E. 1982 “Finite Element Analysis of the Threaded Connections Subjected to External Loads” Bulletin JSME 25 291 298
- Vinogradov, O. Haung, X. 1989 “On A High Frequency Mechanism of Self-Loosening of Fasteners” Proceedings of 12th ASME Conference on Mechanical Vibration and Noise Montreal, Quebec 131 137
- Zadoks, R. I. Yu, X. 1993 “A Preliminary Study of the Self-Loosening in Bolted Connections” ASME Nonlinear Vibrations, ASME Volume DE-Vo l 54 79 88
- Zadoks, R. I. Yu, X. 1997 “An Investigation of the Self-Loosening Behavior of Bolts Under Transverse Vibrations” Journal of Sound and Vibration 208 89 209
- Junker, G. H. 1969 “New Criteria for Self-Loosening of Fasteners Under Vibration” SAE Transactions 78 314 335
- Nassar, S. Housari B. 2006 “Effect of Thread and Bearing Friction on the Vibration-Induced Loosening of Threaded Fasteners” ASME, IMECE Chicago Nov. 2006
- DIN 946 Standard “Determination of Coefficient of Friction of Bolt/Nut Assemblies under specified conditions”
- Nassar, S. A. Ganeshmurthy, S. Ranganathan, R. M. Barber, G. C. “Effect of Tightening Speed on the Torque-Tension and Wear Pattern in Bolted Connections” Journal of Pressure Vessel Technology