This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Simulation-Based Cold-Start Control Strategy for a Diesel Engine with Common Rail Fuel System at Different Ambient Temperatures
Technical Paper
2007-01-0933
ISSN: 0148-7191, e-ISSN: 2688-3627
This content contains downloadable datasets
Annotation ability available
Sector:
Language:
English
Abstract
A new tool has been used to arrive at appropriate split injection strategy for reducing the cranking period during the cold start of a multi-cylinder engine at decreasing ambient temperatures. The concept behind this tool is that the combination of different injection parameters that produce the highest IMEP should be able to improve the cold startability of the diesel engine. In this work the following injection parameters were considered: 1) injection timing, 2) split injection fraction, 3) dwell time and 4) total fuel mass injected per cycle. A commercial engine cyclic simulation code has been modified for diesel engine cycle simulation at lower ambient temperatures. The code was used to develop IMEP control maps. The maps were used to identify the parameters that would give the best IMEP. The strategies that have been identified have been validated experimentally in a multi-cylinder diesel engine equipped with a common rail fuel injection system. The simulation-based strategy proved to be very effective in improving cold start of the diesel engine at ambient temperature as low as -10°C. At temperatures lower than -10°C, the simulation-based strategies don't predict the engine failure to start. The reasons for such failure are analyzed in a sister paper published at the same conference.
Recommended Content
Authors
Citation
Zhong, L., Henein, N., and Bryzik, W., "Simulation-Based Cold-Start Control Strategy for a Diesel Engine with Common Rail Fuel System at Different Ambient Temperatures," SAE Technical Paper 2007-01-0933, 2007, https://doi.org/10.4271/2007-01-0933.Data Sets - Support Documents
| Title | Description | Download |
|---|---|---|
| APPENDIX A | ||
| APPENDIX B |
Also In
SI and CI Engine Cold Start and Transient Emissions and Control
Number: SP-2092; Published: 2007-04-16
Number: SP-2092; Published: 2007-04-16
References
- Atkinson, C. Mott, G. “Dynamic Model-Based Calibration Optimization: An Introduction and Application to Diesel Engines” SAE Paper 2005-01-0026 2005
- Rask, E. Sellnau, M. “Simulation-Based Engine Calibration: Tools, Techniques, and Applications” SAE Paper 2004-01-1264 2004
- Liu, H. Q. “Simulation Model for Steady State and Transient Cold Starting Operation of Diesel Engines” Mechanical Engineering Department, Wayne State University 2001
- Zhong, L.R. Liu, H.Q. Henein, N.A. Bryzik, W. “A Mathematical Model for the cranking Period in the Cold Start of Diesel Engines” IMECE 2003-43990, 2003 ASME International Mechanical Engineing Congress and R&RD Expo Washington D.C., USA 2003
- GT-Power User's Manual, GT-SUITETM Version V6.1 2004
- Girotra, M. Zhong, L.R. Henein, N. A. Bryzik, W. “Split Injection Strategy for Prompt Cold Starting and Low White Smoke Emissions” ICES 2005-01-1100 ASME Internal Combustion Engine Division Chicago 2005
- Zhong, L.R. Gruenewald, S. Henein, N. A. Bryzik, W “Lower Temperature Limits for Cold Starting of Diesel Engine with a Common Rail Fuel Injection System” SAE paper # 07PFL-593 2007
- Zhong, L.R. “A Control Strategy For Cold Starting Of A Diesel Engine With Common Rail Fuel Injection System” Mechanical Engineering Department, Wayne State University 2006
- Yoshizaki, T. Nishida, K. Hiroyasu, H. “Approach to Low NOx and Smoke Emission Engines by Using Phenomenological Simulation” SAE Paper 930612 1993
- Morel, T. Wahiduzzaman, S. “Modeling of Diesel Combustion and Emissions” XXVI FISITA Congress Praha, Czech Republic June 1996
- Xia, Y. Q. Flanagan, R. C. “Ignition Delay - A General Engine/Fuel Model” SAE Paper 870591 1987
- Zhong, L.R. Henein, N. A. Bryzik, W. “A New Predictive ID Model for Advanced High Speed Direct Injection Diesel Engines” ICEF 2004-892, ASME Internal Combustion Engine Division, 2004 Fall Technical Conference Long Beach CA 2004
- Zhong, L.R. Singh, I.P. Han, J. Lai, M-C. Henein, N. A. “Effect of Cycle-to-Cycle Variation in the Injection Pressure in a Common Rail Diesel Injection System on Engine Performance” SAE 2003-01-0699 2003
- Han, Z.P. Henein, N. A. Nitu, B. “Diesel Engine Cold Start Combustion Instability and Control Strategy” SAE Paper 2001-01-1237 2001