This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Advanced Mounting System for Light Duty Diesel Filter
Technical Paper
2007-01-0471
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
This paper employs a systematic approach to packaging design and testing of a system and its components in order to determine the long term durability of light duty diesel filters. This effort has utilized a relatively new aluminum titanate filter technology as well as an advanced support mat technology engineered to provide superior holding force at lower temperatures while maintaining its high temperature performance. Together, these two new technologies form a system that addresses the unique operating conditions of diesel engines. Key physical properties of both the filter and the mat are demonstrated through laboratory testing. The system behavior is characterized by various laboratory techniques and validation procedures.
Recommended Content
Authors
Citation
Nickerson, S., Sawyer, C., Gulati, S., Fernandes, S. et al., "Advanced Mounting System for Light Duty Diesel Filter," SAE Technical Paper 2007-01-0471, 2007, https://doi.org/10.4271/2007-01-0471.Also In
References
- http://www.dieselnet.com/standards/eu/ld.html December 4 2006
- Ogunwumi, S. B. et al. SAE Paper N° 2005-01-0583 2005
- IsoMat AV5 Mat Support System Unifrax Corporation Niagara Falls, NY 2005
- Gulati, S. T. Ten Eyck, J. Lebold, A. SAE Paper N° 922252 1992
- Gulati, S. T. Sherwood, D. L. Corn, S.H. SAE Paper N° 960471 1996
- Tech. Data Blue Sheet Bulletins B-132-Ed5-3M-887 and B-139-Ed5-5M-689-L/J Allegheny Ludlum Corp. Pittsburgh, PA 1989
- Heibel, A. et al. “Performance and Durability Evaluation of the New Corning DuraTrap AT Diesel Particulate Filter - Results from Engine Bench and Vehicle Tests” 193 218 2005
- Fernandes S. et al “Advanced Support Mat Systems for Diesel Emission Control Devices: Addressing Solutions to Cold Holding and Erosion Issues” SAE Paper N° 2006-01-3507 2006
- http://www.euceb.org/downloads_pub/eu_directive_97_69.pdf August 24 2006
- http://www.ilo.org/public/english/protection/safework/cis/legosh/eec/lx070315.htm August 24 2006
- “Commission Directive 97/69/EC of 5 Dec. 1997 adapting to technical progress for the 23rd time Council Directive 67/548/EEC on the approximation of the laws … relating to the classification, packaging and labeling of dangerous substances” Journal officiel des Communautés européennes - Official Journal of the European Communities 13 Dec. 1997 L 343 19 24
- “1000 Cycle Test” Unifrax Corporation Niagara Falls, NY 2004
- Olson J. R. “Diesel Emission Control Devices - Design Factors Affecting Mounting Mat Selection” SAE Paper N° 2004-01-1420 March 2004
- Fernandes S. et al “The Role of New Catalytic Converter Mounting Materials in Providing Durability and Efficiency” SAE Paper N° 2002-01-3447 November 2002
- Fernandes S. et al “Dual Fuel Emission Control Devices - Design Factors Affecting Mounting Mat Selection” SAE BRASIL Paper No. 2004-01-3397 November 2004
- “Catalytic Converter Tech Bulletin - Erosion Durability of Support Mat” Unifrax Corporation Niagara Falls, NY 2004
- Kim J. S. “Theories and Capabilities of Intumescent Mat Numerical Modeling” SAE Paper No. 2003-01-0664 March 2003
- Locker, R. J. Sawyer, C. B. Schmitt, P. S. SAE Paper N° 980042 1998
- Locker, R. J. Sawyer, C. B. Eisenstock, G. SAE Paper N° 2001-01-0223 2001
- Locker, R. J. Sawyer, C. B. “Low temperature catalytic converter durability” SAE Paper N° 2000-01-0220