This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Parametric Study of Physical Requirements for Optimization of the EGR-rate and the Spray Formation for Minimum Emissions Production Over a Broad Range of Load/Speed Conditions
Technical Paper
2006-01-1120
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
The present paper describes a study, which can enable a small displacement (1.3 liter) turbocharged European CR-diesel engine to tolerate an important increase in EGR-level. The analysis is performed by use of a 3D virtual numerical engine model, which isolates the main parameters that must be optimized within the perimeter of the combustion chamber.
The paper gives a short introduction to the physical background for NOx and soot-formation as well as a recall of the main issues related to the simulation models used in the virtual engine simulation. The analysis is performed in a 9 points load/speed test matrix. Several EGR-rates are studied as well as the impact of a precise temperature control of the exhaust gas re-introduced in the intake manifold.
The paper concludes by an analysis of the cumulated impact on the EGR-level tolerated by the engine after the introduction of the suggested optimization measures.
Recommended Content
Authors
Citation
Pontoppidan, M., Demaio, A., Bella, G., and Rotondi, R., "Parametric Study of Physical Requirements for Optimization of the EGR-rate and the Spray Formation for Minimum Emissions Production Over a Broad Range of Load/Speed Conditions," SAE Technical Paper 2006-01-1120, 2006, https://doi.org/10.4271/2006-01-1120.Also In
References
- Amsden, A.A. O'Rourke, P.J Butler, C.D. “KIVA II A Computer Program for Chemical Reactive Flows with Sprays,” Los Alamos National Labs. LA -11560-MS 1989
- Amsden, A.A. O'Rourke, P.J Butler “KIVA III: A KIVA Program with Block Structured Mesh for Complex Geometries” Los Alamos National Labs. LA-12503-MS
- Belardini, P. Bertoli, C. “Multi-dimensional modeling of combustion and pollutants formation of new technology light duty Diesel engines;” Oil & Gas Science and Technology 1999 54 251 257
- Bella G. Rotondi R. Grimaldi C. Postrioti L. “Atomization of High-Pressure Diesel Spray: Experimental Validation of New Breakup Model.” SAE Paper 2001-01-1070
- Bianchi G. Pelloni P. Corcione F. Luppini F. “Numerical Analysis of Passenger Car HSDI Diesel Engines with the 2 nd Generation of Common Rail Injection Systems: The Effect of Multiple Injections on Emissions.” SAE Paper 2001-01-1068
- Halstead M. Kirsch L. Quinn C. “The Autoignition of Hydrocarbon Fuels at High Temperatures and Pressures - Fitting a Mathematical Model.” Combustion and Flame 30 45 60 1977
- Hiroyasu H. Kadota T. Arai M. Bulletin of the JSME 26 569 575 1983
- Immarisio R. Rinolfi, R. “The third generation Direct Injection Diesel engine for Passenger Cars.” ATA Journal 52 1999
- Kaneko I. Matsui R. Matsukado R. Chiba I. “Development of Low Emission Diesel Engine with DPF System.” Proceedings of the 14. Aachner Kolloquium 67 82 2005
- Kee R. J. Rupley F. M. Miller J. A. “Chemkin-II:A Fortran Chemical Kinetics Package for the Analysis of Gas Phase Chemical Kinetics.” Sandia Report SAND89-8009
- Nagle J. Strickland-Constable R. F. Proceedings of the Fifth Carbon Conference 265 325 1962
- Pontoppidan M. Gaviani G. Bella G. Rocco V. “Improvements of GDI-Injector Optimization Tools for Enhanced SI-Engine Combustion Chamber Layout.” SAE Paper 980494
- Pontoppidan M. Gaviani G. Bella G. Rocco V. “Enhanced use of 3-D CFD and Combustion Simulation to Optimize the Development of ECU-Control Algorithms for GDI Spark Ignited Engines.” ICE 99 - Proceedings
- Pontoppidan M. Gaviani G. Bella G. Rocco V. “Enhanced Mixture Preparation Approach for Lean Stratified SI-Combustion by a Combined Use of GDI and Electronically Controlled Valve-Timing.” SAE Paper 2000-01-0532
- Pontoppidan M. Gaviani G. Bella G. Demaio A. Schilardi M “Developments in the Use of Multi-Purpose Numerical Simulation Tools to Optimize Combustion Control Parameters for the 2 nd Generation of Lean Burn, Stratifed GDI Engines.” SAE.”Paper 2001-01-0967
- Pontoppidan M. Ausiello F. Bella G. Demaio A “Study of the Impact of Variations in the Diesel-Nozzle Geometry Parameters on the Layout of Multiple Injection Strategy.” SAE paper 2002-01-0217
- Pontoppidan M. Gaviani G. Bella G. Demaio A “Study of the Benefits and Drawbacks of a Substantial Increase of Rail-Pressure in GDI-Injector Assemblies.” SAE paper 2002-01-1132
- Pontoppidan M. “Combined use of 3D-CFD Simulation and direct Visualization Techniques to decrease the Optimization Procedure Complexity of Combustion chamber Layout and Engine Control Pre-mapping operation necessary for Online Engine Test rig Optimization.” Internationales Symposium für Verbrennungsdiagnostik 2002 Baden-Baden 137 147
- Pontoppidan M. Ausiello F. Bella G. Ubertini S “Study of the Impact on the Combustion Process of Injector Nozzle Layout creating Enhanced Secondary Spray Break-up.” SAE paper 2003-01-0706
- Pontoppidan M. Ausiello F. Bella G. Ubertini S “Study of the Impact on the Spray Shape Stability and the Combustion Process of Supply Pressure Fluctuations in CR-Diesel Injectors.” SAE paper 2004-01-0023
- Pontoppidan M. Gaviani G. Demaio A. Rotondi R. “Reduction of Spray Momentum for GDI High-Pressure Injectors - A necessary step to accomplish Series Production of Super-charged DI-engines.” SAE paper 2005-01-0104
- Pontoppidan M. Demaio A. Serra G. Ubertini S. “Minimization of Particulate Raw Emissions from CR-diesel Engines - A Key-element to limit the Increase in Complexity of Exhaust Gas After-treatment.” SAE paper 2005-01-1235
- Reitz R. D. Song-Charng Kong Bianchi G. M. Falfari S. Pelloni P. “Numerical Analysis of High-Pressure Fast-Response Common Rail Injector Dynamics.” SAE Paper 2002-01-213
- Regulation EPA, Code of Federal Regulations, Title 40 16 “Exhaust gas sampling system, diesel vehicles” 2002
- SAE Surface Vehicle Information Report, SAE nr. J255 February 1995