This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Material Identification using Successive Response Surface Methodology, with Application to a Human Femur Subjected to Three-Point Bending Loading
Technical Paper
2006-01-0063
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
Material and structural properties of human tissues under impact loading are needed for the development of physical and computational models used in pedestrian and vehicle occupant protection. Obtaining these global properties directly from the data of biomechanical tests is a challenging task due to nonlinearities of tissue-test setup systems. The objective of this study was to develop subject-specific finite element (FE) techniques for material identification of human tissues using Successive Response Surface Methodology. As example, the test data of a human femur in three-point bending is used to identify parameters of cortical bone. Good global and local predictions of the optimized FE model demonstrate the utility and effectiveness of this new material identification approach.
Recommended Content
Technical Paper | Computer Modeling in New Vehicle Design |
Technical Paper | Impact Simulation of Simplified Structural Models of Aircraft Fuselage |
Technical Paper | Modeling Tools for Design of Air Cushion Restraint Systems |
Authors
Topic
Citation
Untaroiu, C., Kerrigan, J., and Crandall, J., "Material Identification using Successive Response Surface Methodology, with Application to a Human Femur Subjected to Three-Point Bending Loading," SAE Technical Paper 2006-01-0063, 2006, https://doi.org/10.4271/2006-01-0063.Also In
SAE 2006 Transactions Journal of Passenger Cars: Mechanical Systems
Number: V115-6; Published: 2007-03-30
Number: V115-6; Published: 2007-03-30
References
- An, Y.H. Draughn R.A. 2000 Mechanical Testing of Bone and the Bone-Implant Interface CRC Press Boca Raton
- Ashman, R.B. Cowin S.C. Van Buskirk W.C. Rice J.R. 1984 “A continuous wave technique for the maeasurement of the elastic properties of bone” J. of Biomechanics 17 349 361
- Burstein, A.H Reilly D.T. Martens, M. 1976 “Aging of bone tissue: mechanical properties” J. Bone Joint Surg. 58A 82
- Chong, E.K.P. 2001 “An introduction to optimization” Willey
- Funk J.R. Kerrigan J.R Crandall J.R. 2004 “Dynamic Bending Tolerance and Elastic-Plastic Material Properties of the Human Femur” 48th Proceeding of AAAM
- Hallquist, J. O. May 1998 LS-Dyna Theoretical Manual
- Katsamanis F. Raftopoulos D.D. 1990 “Determination of mechanical properties of human femoral cortical bone by the Hopkinson bar stress technique” Journal of Biomechanics 23 1173 1184
- Kong, L. B. Lekawa, M. Navarro, R. A. McGrath, J. Cohen, M. Margulies, D. R. Hiatt, J. R. 1996 “Pedestrian-motor vehicle trauma: an analysis of injury profiles by age” American College of Surgeons Journal 182 (1) 17 23
- Knets, I. Malmeisters, A 1977 “Deformability and strength of human compact bone tissue “ Brankov G. Mechanics of Biological Solids: Proceeding of the Euromech Colloquium 68, Varna, Bulgaria September 1975 Bulgarian Academy of Sciences Sofia 133 141
- Luenberger D 2003 Linear and nonlinear programming Kluwer
- Montgomery, D. C. 2005 Design and Analysis of Experiments John Wiley
- Oden, Z.M. Hart, R.T. Burr, D.B. 1993 “The influence of assumed relationships between bone’s mechanical properties and CT density on results of finite element analyses” IEEE Biomedical Engineering Conference 57 59
- Reilly, D.T. Burstein A.H. 1975 “The elastic and ultimate properties of compact bone tissue” J. of Biomechanics 8 393 405
- Rho, J.Y. Hobatho, M.C. R.B. Ashman 1995 “Relations of mechanical properties to density and CT numbers in human bone” Med. Eng. Phys. 17 347 355
- Skalak, R. Chien, S. 1987 Handbook of Bioengineering McGraw-Hill New York 2.19
- Schuster, P.J. Chou C.C. Prasad P. Jayaraman, G. 2000 “Development and Validation of a Pedestrian Lower Limb Non-Linear 3-D Finite Element Model” Stapp Car Crash Journal 44 2000-01-SC21
- Snedeker J.G. Muser M. Walz F.H. 2003 “Assessment of Pelvis and Upper Leg Injury Risk in Car-Pedestrian Collisions: Comparison of Accident Statistics, Impactor Tests and a Human Body Finite Element Model” 47th Stapp Car Crash Conference, Paper No. 2003-22-0019
- Snyman, J.A. 1982 “A New and Dynamic Method for Unconstrained Minimization” Appplied Mathematical Modelling 6 449 462
- Stander N. 2003 LS-OPT User’s Manual, Design Optimization for Engineering Analysis
- Takahashi, Y. Kikuchi Y. Konosu A. Ishikawa H. 2000 “Development and Validation of the Finite Element Model for the Human Lower Limb of Pedestrians.” Stapp Car Crash Journal 44 2000-01-SC22
- Untaroiu C. Darvish K. Crandall J. Deng B. Wang J.T. 2005 “A Finite Element Model of the Lower Limb for Simulating Pedestrian Impacts” Stapp Car Crash Journal 49
- Untaroiu C. Darvish K. Crandall J. Deng B. Wang J.T. 2005 “A Finite Element Model of the Lower Limb for Simulating Pedestrian Impacts” Paper # IMECE2004-61583, 2004 ASME Congress, Anaheim, CA
- World Bank Group: Road Safety 2006 http://www.worldbank.org/transport/roads/safety.htm
- Yoon, H.S. Katz J.L. 1976 “Ultrasonic wave propagation in human cortical bone: II. Measurements of elastic properties and micro-hardness J. of Biomechanics 9 459 464