This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Optimization of Off-highway Engine for TIER-II Emission Norms Using Cost Effective Fuel Injection Equipment
Technical Paper
2005-26-006
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Event:
SIAT 2005
Language:
English
Abstract
A major task faced by engine manufacturers all over the world is to upgrade running engine designs with least possible modifications to meet next level of emission norms. This saves the precious lead-time and investments. In addition simplicity of design has to be maintained as far as possible while improving emissions. This is possible only by optimal combinations of FIE and engine. This paper describes such a cost effective up-gradation of an engine from US Tier 1 to US Tier 2 in very short time with minimal design changes. This difficult task was achieved by using latest techniques of simulations, measurements and concurrent engineering. For variable speed application it is desirable to retard injection timing as speed decreases, to compensate gain in absolute time. For constant speed application, retardation at part load is required as more weightage is given at part loads for the emission test cycle. The required injection characteristics were achieved by means of stepped plunger. Exhaustive endurance tests validated the modified design. This technology is being implemented on other variants of this engine. Optimum injection timing to meet combustion requirements at different operating conditions and shaping of fuelling curve to meet output demands results in better emissions without affecting other characteristics like fuel consumption, torque and startability.
Authors
- Y. V. Aghav - Kirloskar Oil Engines Limited, Pune, India
- N. S. Nayak - Kirloskar Oil Engines Limited, Pune, India
- B. S. Deshmukh - Kirloskar Oil Engines Limited, Pune, India
- N. P. Gokhale - Kirloskar Oil Engines Limited, Pune, India
- P. V. Reddy - Kirloskar Oil Engines Limited, Pune, India
- A. D. Dani - Kirloskar Oil Engines Limited, Pune, India
- S. S. Sudambi - Motor Industries Co. Ltd, Bangalore, India
- R. S. Reddy - Motor Industries Co. Ltd, Bangalore, India
Topic
Citation
Aghav, Y., Nayak, N., Deshmukh, B., Gokhale, N. et al., "Optimization of Off-highway Engine for TIER-II Emission Norms Using Cost Effective Fuel Injection Equipment," SAE Technical Paper 2005-26-006, 2005, https://doi.org/10.4271/2005-26-006.Also In
References
- Lakshminarayanan, P. A. et al. “Accurate Prediction of the Rate of Heat Release in a Modern Direct Injection Diesel Engine” Imech E 216 J. of Automobile 2002
- Melde-Tuczai H. et al. “Ways to Meet Future Emission Regulations for Agricultural Tractor Engines” SAE paper 2001-01-0007
- Best C. H. et al. “Diesel Engine Technology Needs for India for Net Five Years” SAE paper 2001-28-0008
- Furuta, K. Sasaki, S. Tokuda, M. “Study of the In-Line Pump System for Diesel Engines to Meet Future Emission Regulations” SAE paper 980812
- Campbell G L et al. “New John Deere 2.9L 3-Cylinder Diesel Engines” SAE paper 921698
- Kubota, K. Ohashi, R. Taniguchi, H. “The Ultra-mini Fuel Injection Pump Development for Small Air-cooled Diesel Engines” SAE paper 850069
- Heywood, J. B. “A Text Book on Internal Combustion Engine Fundamentals” McGraw-Hill International editions 1988
- Dani, A. D. Nagpurkar, U. P. Lakshminarayanan, P. A. “Universal Mixing Correlations for the Performance and Emission of Open Chamber Diesel Combustion Supported by Air Swirl” SAE paper 900446
- Primus, R. J. “Visual Thermodynamics: Processes in Log(p)-Log(T) Space” SAE paper 1999-01-0516
- Lakshminarayanan, P. A. et al. “Predicting Hydrocarbon Emissions From Direct Injection Diesel Engine” ASME 124 2002
- Johnson, J. H. et al. “A Review of Diesel Particulate Control Technology and Emissions Effect” SAE paper 940233