This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Innovative metal supported catalysts for EU V Diesel Engines
Technical Paper
2005-24-003
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
Future stringent emission levels for NOx and PM will lead to the introduction of innovative combustion processes for diesel engines, such as premixed combustion, with the results to enhance the engine out emission of HC and CO. Therefore very efficient oxidation catalyst will be needed to face this possible issue. This paper deals with the optimization of a EU IV exhaust system by means of innovative metal supported catalyst, as for example the Pre Turbo Catalyst and the Hybrid Catalyst in combination with dedicated catalyst coatings. Moreover a base study over the use of PM-Filter Catalyst has been made, to show the efficiency of such a device with EU IV engine calibration. The second part of the paper deals with the turbulent like structured foils substrates to have an even more efficient diesel oxidation catalyst with very high volumetric efficiency.
Authors
Topic
Citation
Presti, M., Pace, L., Carelli, G., Spurk, P. et al., "Innovative metal supported catalysts for EU V Diesel Engines," SAE Technical Paper 2005-24-003, 2005, https://doi.org/10.4271/2005-24-003.Also In
References
- Imarisio, R. Peters, B. Rossi Sebastiano, G.M. Pinson, J. Boretto, G. Buratti, R. Powertrain, Fiat GM “Diesel Strategies towards Fuel Neutral European Emission Standards” Paper 04A5010, ATA Symposium, Bari (Italy) 2004
- Herzog Dr. AVL List G.m.b.H. “Future HSDI Diesel Combustion Strategies” 4th Advanced Diesel Engine Technology Symposium Seoul 2004
- Hosogai, Dipl.-Ing. S. Komatsu, Dipl.-Ing. K. Unno, Dipl.-Ing. Y. „Der Hybridkatalysator – ein neues Katalysatorkonzept zur verbesserten Ausnutzung der Abgasenergie und Steigerung der Effektivität von Dieselkatalysatorsystemen“ International Vienna Motor Symposia Wien 2003
- Schaper, Katrin Konieczny, Roman Brück, Rolf G.m.b.H. Emitec Deutschland; „Diesel catalytic converter with hybrid substrate structure“ Haus der Technik e. V., Essen 15. und 16. Juni 1999
- Nilsson, P. Diefke, F. Lundgren, M. Brück, R. Kruse, C. Schaper, S. „Neue Dieselkatalysatorsysteme zur Erreichung der europäischen Grenzwerte 2005 – Getestet an einem Volvo S60 Personenkraftwagen“ 24 Internationales Wiener Motorensymposium
- Jacob, E. Dr. D′Alfonso, N. Dr. Döring, A. Reisch, S. Rothe, D. Brück, R. Treiber, P. Dr. „PM-Kat: Nichtblockierende Lösung zur Minderung von Dieselruß für Euro IV-Nutzfahrzeugmotoren“ 23 Internationales Wiener Motorensymposium April 2002
- Brück, Rolf Hirth, Peter Reizig, Meike Treiber, Peter Breuer, Jürgen GmbH, Emitec „Metal Supported Flow-Through Particulate Trap; a Non-Blocking Solution“ SAE Paper 2001-01-1950
- Jacob, E. Dr. MAN Nutzfahrzeuge Gruppe Geschäftseinheit Motoren Nürnberg „Zukünftige Konzepte im Nutzfahrzeug“
- Bollig, M. Liebl, J. Zimmer, R. Kraum, M. Seel, O. Siemund, S. Brück, R. Diringer, J. Maus, W. GmbH, Emitec „Next generation catalysts are turbulent: development of support and coating” SAE Paper 2004-01-1488
- Pace, Lorenzo Konieczny, Roman Presti, Manuel GmbH, Emitec “Metal Supported Particulate Matter-Cat, a Low Impact and Cost Effective Solution for the FIAT 1.3 JTD Euro IV Engine” SAE Paper 2005-01-0471
- Spurk, P. Schütze, F.-W. Lox, E. Umicore, Brück,A. R. Schatz, EMITEC Potential strukturierter Metallträger und fortschrittlicher Beschichtungen, getestet an einem EU IV 2,2 l Dieselfahrzeug 2 Emission Control 2004 Dresden