This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
A Predictive Model for Feedgas Hydrocarbon Emissions: An Extension to Warm Engine Maps
Technical Paper
2005-01-3862
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
A feedgas hydrocarbon emissions model that extends the usefulness of fully-warmed steady-state engine maps to the cold transient regime was developed for use within a vehicle simulation program that focuses on the powertrain control system (Virtual Powertrain and Control System, VPACS). The formulation considers three main sources of hydrocarbon. The primary component originates from in-cylinder crevice effects which are correlated with engine coolant temperature. The second component includes the mass of fuel that enters the cylinder but remains unavailable for combustion (liquid phase) and subsequently vaporizes during the exhaust portion of the cycle. The third component includes any fuel that remains from a slow or incomplete burn as predicted by a crank angle resolved combustion model. The hydrocarbon model estimates the oxidized portion of these fuel sources according to a simplified empirical model incorporating exhaust port temperature predictions from a simple, heat transfer-based pipe model. Calibration of the hydrocarbon model to a base vehicle/powertrain/engine run allows estimates of feedgas hydrocarbons when changes are made to vehicle calibration, hardware, or external environment. Agreement between the hydrocarbon model prediction and vehicle data measurements for a range of vehicle calibrations is excellent.
Recommended Content
Topic
Citation
Strayer, B. and Trinker, F., "A Predictive Model for Feedgas Hydrocarbon Emissions: An Extension to Warm Engine Maps," SAE Technical Paper 2005-01-3862, 2005, https://doi.org/10.4271/2005-01-3862.Also In
References
- DeLosh, R.G. Brewer, K.J. Buch, L.H. Ferguson, T.F.W. Tobler, W.E. “Dynamic Computer Simulation of a Vehicle with Electronic Engine Control” SAE # 810447 1981
- Curtis, E.W. Aquino, C.F. Trumpy, D.K. Davis, G.C. “A New Port and Cylinder Wall Wetting Model to Predict Transient Air/Fuel Excursions in a Port Fuel Injected Engine” SAE # 961186 1996
- Batteh, J.J. Curtis, E.W. “Modeling Transient Fuel Effect with Alternative Fuels” SAE # 2005-01-1127 2005
- Dai, W. Cheemalamarri, S. Curtis, E.W. Boussarsar, R. Morton, R.K. “Engine Cycle Simulation of Ethanol and Gasoline Blends” SAE # 2003-01-3093 2003
- Tabaczynski, R.J. Ferguson, C.R. Radhakrishnan, K. “A Turbulent Entrainment Model for SI Engine Combustion” SAE # 770647 1977
- Davis, G.C. Kent, J.C. “Comparison of Model Calculations and Experimental Measurements of the Bulk Cylinder Flow Processes in a Motored PROCO Engine” SAE #790296 1979
- Borgnakke, C. Davis, G.C. Tabaczynski, R.J. “Predictions of In-Cylinder Swirl Velocity and Turbulence Intensity for an Open Chamber Cup=in-Piston Engine” SAE # 810224 1981
- Newman, C.E. Davis, G.C. “GESIM Operation Theory” Ford Motor Co Research Report 1994
- Dai, W. Russ, S.G. Trigui, N. Tallio, K.V. “Regimes of Premixed Turbulent Combustion and Misfire Modeling in SI Engines” SAE # 982611 1998
- Shayler, P.J. Darnton, N.J. Ma T. “Factors Influencing Drive Cycle Emissions and Fuel Consumption” SAE # 971603 1997
- Shayler, P.J. Belton, C. Scarisbrick, A. “Emission and Fuel Utilisation After Cold Starting Spark Ignition Engines” SAE# 1999-01-0220 1999
- Santoso, H. Cheng, W.K. “Mixture Preparation and Hydrocarbon Emissions Behaviors in the First Cycle of SI Engine Cranking” SAE # 2002-01-2805 2002
- Hallgren, B.E. Heywood, J.B. “Effects of Substantial Spark Retard on SI Engine Combustion and Hydrocarbon Emissions” SAE# 2003-01-3236 2003
- Trinker, F.H. Cheng, J. Davis, G.C. “A Feedgas HC Emissions Model for SI Engines Including Partial Burn Effects” SAE # 932705 1993
- Cheng, W.K. Hamrin, D. Heywood, J.B. Hochgreb, S. Min, K. Norris, M. “An Overview of Hydrocarbon Emissions Mechanisms in Spark-Ignition Engines” SAE # 932708 1993