This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
A Composition-Based Model for Particulate Matter Emission of Direct Injection Diesel Engines
Technical Paper
2005-01-3463
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
In this study, a composition-based particulate matter (PM) model of direct injection diesel engines has been formulated and developed to simulate PM emission. The PM model is based on formation mechanisms of main compositions of PM: soot and soluble organic fraction (SOF). Firstly, two models for soot and SOF emissions are established respectively, then, the two models are integrated into a whole PM model. The soot emission model is given by the difference between a primary formation model and an oxidation model of soot. The soot primary formation model is the Hiroyasu soot formation model, and the Nagle and Strickland-Constable model for the soot oxidation is adopted. The SOF emission model is based on an unburned hydrocarbons (HC) emission model, and the HC model is given by the difference between a HC primary formation model and a HC oxidation model. The HC primary formation model considers that fuel injected and mixed beyond the lean combustion limit during ignition delay and fuel effusing from the nozzle sac volume at low pressure and low velocity.
In order to validate the model, experiments were performed on a six-cylinder, turbocharged and intercooled, direct injection diesel engine. The simulation results show good agreement with the experimental data, and it indicates the validity of the PM model. The calculation results show distinctions between PM and soot formation rates are mainly in the early combustion stage. The SOF formation has important influence on the PM formation at lower loads, and the soot formation dominates the whole PM formation process at higher loads. The PM model is helpful for better understanding the PM emission formation process of diesel engines, and useful for the simulation of PM emission, as well as PM emission control of diesel engines.
Recommended Content
Authors
- Pi-qiang TAN - School of Automobile, Tongji University
- kang-yao DENG - Institute of Internal Combustion Engine, Shanghai Jiaotong University
- Jia-xiang LU - School of Energy and Power Engineering, Shandong University
- Di-ming LOU - School of Automobile, Tongji University
- Gang WAN - School of Automobile, Tongji University
Citation
TAN, P., DENG, k., LU, J., LOU, D. et al., "A Composition-Based Model for Particulate Matter Emission of Direct Injection Diesel Engines," SAE Technical Paper 2005-01-3463, 2005, https://doi.org/10.4271/2005-01-3463.Also In
References
- Hou Z X Abraham J Three-Dimensional Modeling of Soot and NO in a Direct Diesel Engine SAE Paper 950608 1995
- Mickllow G J Gong W Combustion modelling for direct injection diesels Proc. Instn. Mech.Engrs, Part D, Journal of Automobile Engineering 215 651 663 2001
- Gao Z Schreiber W A multizone analysis of soot and NOx emission in a D.I. diesel as a function of engine load, wall temperature, and intake air O 2 content ASME Paper 2000-ICE-314 35-1 133 142 2000
- Welch S Moss J B Zonal modelling of diesel engine smoke emission IMechE Paper C499/027/96 1996
- Ouenou Gamo S Ouladsine M Rachid A Diesel engine exhaust emissions modelling using artificial neural networks SAE Paper 1999-01-1163 1999
- Golovitchev V L Niklas N Detailed chemistry sub-grid model of turbulent spray combustion for the KIVA code ASME Paper 99-ICE-237 33-3 17 25 1999
- Thompson G J Atkinson C M Clark N N Long T W Hanzevack E Neural network modelling of the emissions and performance of a heavy-duty diesel engine Proc. Instn. Mech. Engrs, Part D, Journal of Automobile Engineering 214 111 126 2001
- Pertti T Philipp V H Reijo K Liljenfeldt G Salminen H J Simulation of combustion, soot and NOx emissions in a large medium speed diesel engine SAE paper 981449 1998
- Mansouri S H Bakhshan Y Studies of NOx, CO, soot formation and oxidation from a direct injection stratified-charge engine using the k-ε turbulence model Proc. Instn. Mech. Engrs, Part D, Journal of Automobile Engineering 215 95 104 2001
- Ubanwa B Burnette A Kishan S Fritz S G Exhaust particulate matter emission factors and deterioration rate for in-use motor vehicles ASME Paper 2000-ICE-269 34-2 7 16 2000
- Yi Y Hessel R Reitz R The influence of physical input parameter uncertainties on multi-dimensional model predictions of diesel engine performance and emissions SAE Paper 2000-01-1178 2000
- De Risi A Manieri D F Laforgia D A theoretical investigation on the effects of combustion chamber geometry and engine speed on soot and NOx emissions ASME Paper 99-ICE-207 33-1 51 59 1999
- Colin R F Allen T K Internal Combustion Engine John Wiley & Sons New York 2001
- Heywood J B Internal Combustion Engine Fundamentals McGraw-Hill New York 1988
- Hiroyasu H Kadota T Arai M Development and Use of a Spray Combustion Modeling to Predict Diesel Engine Efficiency and Pollutant Emissions, Part 1: Combustion Modeling Bulletin of the JSME 26 214 569 575 1983
- Feng T Numerical Modeling of Soot and NOx Formation in Non-Stationary Diesel Flames with Complex Chemistry Chalmers University of Technology 2002
- Assanis D N Filipi Z S Fiveland S B et al A Predictive Ignition Delay Correlation under Steady-State and Transient Operation of a Direct Injection Diesel Engine Journal of Engineering for Gas Turbines and Power 125 450 457 2003