This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
The Effect of Micro-Geometry and Load on Helical Gear Noise Excitations
Technical Paper
2005-01-2295
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
The prediction of gear noise may normally be treated as a classical source - path - receiver problem. Usually, the excitation occurs in the gear mesh and the path includes the transmission of forces and motions through the shafts and bearings to the gear housing, which in turn radiates the noise. This paper focuses on the source aspect of the problem and identifies the major sources of gear whine noise and develops a metric that incorporates these sources into a single equation. An example then shows how the micro-topography of a gear set affects several of the excitation components. A computer program that predicts the load distribution and motion errors of a gear pair is used for the analyses.
Recommended Content
Authors
Topic
Citation
Houser, D. and Harianto, J., "The Effect of Micro-Geometry and Load on Helical Gear Noise Excitations," SAE Technical Paper 2005-01-2295, 2005, https://doi.org/10.4271/2005-01-2295.Also In
References
- Houser, D. R. “Gear Noise Sources and Their Prediction Using Mathematical Models,” Gear Design Manufacturing and Inspection Manual SAE 1990 213 222
- Welbourn, D. B. “Fundamental Knowledge of Gear Noise - A Survey” Inst. Mech. Eng. Conf. on Noise and Vibration of Engines and Transmissions Inst. Mech. Eng. Aut. Div. 1979 9 14
- Niemann, G. Baethke, J. “Transmission Error, Tooth Stiffness and Noise of Spur and Helical Gears, Part 1 (Drehwegfehler, Zahnfederharte und Gerausch bei Stirnradern),” VDIZ Vol 112 1970
- Baron, E. Favre, B. Mairesse “Analysis of Relation Between Gear Noise and Transmission Error,” Proc. INTERNOISE-88 1988
- Kubo, A. Nonaka, T. Kato, N. Kato, S. Ohmori, T. “Representative Form Accuracy of Gear Tooth Flanks on the Prediction of Vibration and Noise of Power Transmission,” AGMA Paper 92FTM9
- Mark, W. D. “Gear Noise Excitation,” Plenum Press New York 1989
- Börner, J. Houser, D. R. “Friction and Bending Moments on Gear Noise Excitations,” SAE, Paper 961816 Vol. 105 No. 6 1669 1676
- Houser, D. R. Harianto, J. “Design Robustness and Its Effect on Transmission Error and Other Design Parameters,” The International Conference on Mechanical Transmission 2001
- Vaishya, M. Houser, D. R. “Modeling and Analysis of Sliding Friction in Gear Dynamics,” Proc. of DETC'2000, ASME Power Transmission and Gearing Conference 2000
- Ishida, S. “On the Friction Noise and Pitch Circle Impulsive Noise of Gears,” Proc. JSME Semi-International Symposium 1967 161 170
- Iida, H. Tamura, A. Yamada Y. “Vibrational Characteristics of Friction Between Gear Teeth,” Bulletin of the JSME 1985 July Vol 28 No 241 1512 1519
- Donley, M. G. Lim, T. C. Steyer, G. C. “Dynamic Analysis of Automotive Gearing Systems,” SAE International Congress and Exposition 1992 SAE Paper 920762 77 87
- Campbell, B. Stokes, W. Steyer, G. Clapper, M. Krishnaswami, R. Gagnon, N. “Gear Noise Reduction of an Automatic Transmission Through Finite Element Dynamic Simulation,” Proc., SAE Automotive NVH Conference , SAE Paper 971966 1997
- Hochmann, D. Houser, D. R. “Friction Forces as a Dynamic Excitation Source in Involute Spur and Helical Gearing,” Proc. of DETC'2000, ASME Power Transmission and Gearing Conference 2000
- Vijayakar, S. M. Houser, D. R. “Contact Analysis of Gears Using a Combined Finite Element and Surface Integral Method,” AGMA Fall Technical Meeting 1991, 91FTM16 and Gear Technology, July/August 1993 26 33
- Houser, D. R. Harianto, J. “Load Distribution Program Manual,” The Ohio State University 2002
- Houser, D. R. Oswald, F. B. Valco, M. J. Drago, R. J. Lenski, J. W. “Comparison of Transmission Error Predictions with Noise Measurements for Several Spur and Helical Gears,” Proc. 30th AIAA/ASME/SAE/ASEE Joint Propulsion Conf. 1994
- Gregory, R. W. Harris, S. L. Munro, R. G. “Dynamic Behavior of Spur Gears,” Proc. I. Mech. E. No. 8 Apr. 1953 207 226
- Maki, H. “A Study on Definitions of Tooth Modifications of Helical Gears Relevant to Gear Noise,” The JSME Int. Conf. on Motion and Power Transmissions 2001 57 67