This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Seat Belt Buckle Performance in High Energy Wheel-to-Ground Impacts
Technical Paper
2005-01-1709
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
For more than 20 years, field research and laboratory testing has consistently demonstrated that wearing a seat belt dramatically reduces the risk of occupant death or serious injury in motor vehicle crashes. The injury prevention benefits of seat belts require that they remain fastened during collisions. Federal Motor Vehicle Safety Standards and SAE Recommended Practices set forth seat belt buckle performance requirements to ensure proper buckle performance in accident conditions. Numerous analytical and laboratory studies have investigated buckle inertial properties. While studies have shown that current buckle designs have inertial release thresholds well above conditions believed to occur in real-world crashes, there is limited data characterizing severe wheel to ground impacts.
This study investigates seat belt buckle responses to severe wheel to ground impacts. This is accomplished through the analysis of accelerations during full vehicle drop tests. Amplification of the amount necessary for seat belt buckle inertial release did not occur. These tests also confirm that the magnitudes and durations of the accelerations recorded at the buckle were well below those necessary for inertial release. While no simulation can replicate all field crash scenarios, the acceleration analyses can provide engineers with an effective diagnostic tool for assessing seat buckle performance in realistic high energy crash scenarios.
Recommended Content
Technical Paper | Issues in Seatbelt Inertial Release |
Technical Paper | Seat Belt Retractor Performance Evaluation in Rollover Crashes |
Technical Paper | Dynamic Response of End-Release Buckles to Floor Anchor Impulses |
Authors
Citation
Klima, M., Toomey, D., and Weber, M., "Seat Belt Buckle Performance in High Energy Wheel-to-Ground Impacts," SAE Technical Paper 2005-01-1709, 2005, https://doi.org/10.4271/2005-01-1709.Also In
Air Bags, Occupant Protection, and Child Passenger Restraints
Number: SP-1933; Published: 2005-04-11
Number: SP-1933; Published: 2005-04-11
SAE 2005 Transactions Journal of Passenger Cars: Mechanical Systems
Number: V114-6; Published: 2006-02-01
Number: V114-6; Published: 2006-02-01
References
- Orlowski, K.F. Bundorf, R.T. Moffatt, E.A. Rollover Crash Tests-The Influence of Roof Strength on Injury Mechanics Paper No. 8517341984 , Society of Automotive Engineers 1985
- Bahling, G.S. Bundorf, R.T. Kaspzyk, G.S. Moffatt, E.A. Orlowsi, K.F. Stocke, J.E. Rollover and Drop Tests - The Influence of Roof Strength on Injury Mechanics Using Belted Dummies Paper No. 902314 , Society of Automotive Engineers 1990
- Moffatt, E.A. Thomas, T.M. Cooper, E.R. Safety Belt Buckle Inertial Responses in Laboratory and Crash Tests Paper No. 950887 , Society of Automotive Engineers 1995
- National Highway Traffic Safety Administration Traffic Safety Facts 2002: Occupant Protection
- National Highway Traffic Safety Administration Fatality Reduction by Safety Belts for Front-Seat Occupants of Cars and Light Trucks: Updated and Expanded Estimates Based on 1986-1999 FARS Data NHTSA Technical Report DOT HS 809 199 December 2000
- “Standard No. 209; Seat belt assemblies” Code of Federal Regulations
- James, M.B. Allsop, D. Perl, T.R. Struble, D.E. Inertial Seatbelt Release Paper No. 930641 , Society of Automotive Engineers 1993
- Davee, D. Van Arsdell, W. Raasch, C. Paper No. 2004-01-0854 Minimal Effect of Amplified Vehicle Accelerations on Seat Belt Buckle Resistance to Inertial Release Society of Automotive Engineers 2004
- National Highway Traffic Safety Administration, Engineering Test Facility “Tests Regarding Alleged Inertial Unlatching of Safety Belt Buckles” NHTSA Office of Defects Investigation, Final Report VRTC-72-0280 November 1992
- National Highway Traffic Safety Administration, Office of Defects Investigation “Inadvertent Release of Seat Belt Buckles” November 18 1992
- Andreatta, D. Wiechel, J.F. MacLaughlin, T.F. Guenther, D.A. An Analytical Model of the Inertial Opening of Seat Belt Latches Paper No. 960436 , Society of Automotive Engineers 1996
- Clarke, R. Sances, A. Jr, Vertical Impulse Analysis of Seat Belt Buckles Paper No. IMECE2002-32639, American Society of Mechanical Engineers International Mechanical Engineering Congress and Exposition New Orleans, Louisiana November 2002
- Andrews, S.B. Roberts, H.A. Partain, J.F. Renfroe, D.A. Dynamic Characteristics of End Release Seatbelt Buckles Paper No. 97, 17th International Technical Conference on the Enhanced Safety of Vehicles Amsterdam, The Netherlands National Highway Safety Administration June 2001
- Sances, A. Jr., Kumaresan, S. Clarke, R. Renfroe, D. Herbst, B. Pozzi, M. Biomechanical Analysis of Motor Vehicle Seat Belt Buckles Paper No. 2003-041, Instrumentation, Systems, and Automation Society 2003
- Herbst, B. Meyer, S.E. Forrest, S. Sances, A. Kumaresan, S. Acceleration Amplification in Safety Belt Buckle Systems Paper No. IMECE2003-43159, American Society of Mechanical Engineers International Mechanical Engineering Congress and Exposition Washington, DC November 2003
- Society of Automotive Engineers International Surface Vehicle Recommended Practice: (R) Instrumentation for Impact Test, Part 1, Electronic Instrumentation SAE J211-1 March 1995 Society of Automotive Engineers 2003
- Grenke, B.D. Digital Filtering for J211 Requirements using a Fast Fourier Transform Based Filter Paper No. 2002-01-0796 , Society of Automotive Engineers 2002