This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Estimation of the Instantaneous In-Cylinder Pressure for Control Purposes using Crankshaft Angular Velocity
Technical Paper
2005-01-0228
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
Instantaneous in-cylinder pressure, a key variable in the improvement of engine performance and reduction of emissions, is not likely to be measured directly in production type engines in the near future. As a countermeasure, a pressure estimation method based on physical first principles for the estimation of the instantaneous in-cylinder pressure of an SI engine using measured crankshaft angular velocity is presented here.
The approach consists of (a) mapping the model parameters at nominal operating conditions and (b) adapting the model parameters to current operating conditions using the instantaneous crankshaft angular velocity. The model reflects all essential effects on in-cylinder pressure, while the simulation time was reduced to 6 milliseconds per cycle on a standard PC. This makes it possible to estimate a cylinder-averaged pressure for each cycle up to an engine speed of more than 6000 rpm. The estimated in-cylinder pressure is available with a delay of one engine cycle.
The model has been compared to a benchmark pressure estimation method. Further, the model has been validated in simulation and against measured data for steady-state and transient operation. The model shows good accuracy, while the computational effort is promising for real-time applications. Furthermore, the model needs little calibration effort due to its physically based nature.
Recommended Content
Authors
Citation
Brand, D., Onder, C., and Guzzella, L., "Estimation of the Instantaneous In-Cylinder Pressure for Control Purposes using Crankshaft Angular Velocity," SAE Technical Paper 2005-01-0228, 2005, https://doi.org/10.4271/2005-01-0228.Also In
References
- Andersson I. Eriksson L. Ion sensing for combustion stability control of a spark-ignited, direct-injected engine SAE 2000-01-0552 2000
- Azzoni P. M. Minelli G. Moro D. Flora R. Serra G. Indicated and Load Torque Estimation using Crankshaft Angular Velocity Measurement SAE 1999-01-543 1999
- Ball J. K. Bowe M. J. Stone C. R. Mc-Fadden P.D. Torque estimation and misfire detection using block angular acceleration SAE 2000-01-0560 2000
- Chen S.X. Moskwa J.J. Application of nonlinear sliding-mode observer for cylinder pressure reconstruction Control Engineering Practice 5 8 1115 1121 1997
- Citron J.S. O'Higgins J.E. Chen L.Y. Cylinder by Cylinder Engine Pressure and Pressure Torque Waveform Determination Utilizing Speed Fluctuations SAE 890486 1989
- Connolly F. T. Yagle A. E. Modeling and Identification of the Combustion Pressure Process in Internal-Combustion Engines Mechanical Systems and Signal Processing 8 1 1 19 1994
- Csallner Peter Woschni Gerhard Zur Vorausberechnung des Brennverlaufes von Ottomotoren bei geäanderten Betriebsbedingungen MTZ Motortechnische Zeitschrift 43 1982 195 200 1982
- Eriksson L. Nielsen L. Towards On-Board Engine Calibration with Feedback Control Incorporating Combustion Models and Ion-sense Automatisierungstechnik 5 2003
- Fehrenbach H. Berechnung des Brennraumdruckverlaufes aus der Kurbelwellen-Winkelgeschwindigkeit von Verbrennungsmotoren 255 Reihe 6 Energieerzeugung of Fortschritt-Berichte VDI VDI Verlag Düusseldorf 1991
- Guezennec Y. Gyan P. A novel Approach to Real-Time Estimation of the Individual Cylinder Combustion Pressure for S.I. Engine Control SAE 1999-01-0209 1999
- Gyan P. Ginoux S. Champoussin J.-C. Guezennec Y. Crankangle Based Torque Estimation: Mechanistic/Stochastic SAE 2000-01-0559 2000
- Heywood J.B. Internal Combustion Engine Fundamentals Mc-Graw-Hill 1988
- Hires S. D. Tabaczynski R. J. Novak J. M. The Prediction of Ignition Delay and Combustion Intervals for a Homogeneous Charge, Spark Ignition Engine SAE 780232 1978
- Matekunas F.A. Modes and measures of cyclic combustion variability SAE 830337 1983
- Mladek M Cylinder Pressure for Control Purposes of Spark Ignition Engines ETH Zürich 2003
- Müller R. Hart M. Krötz G. Eickhoff M. Truscott A. Noble A. Cavalloni C. Gnielka M. Combustion Pressure Based Engine Management System SAE 2000-01-0928 2000
- Powell J.D. Engine Control Using Cylinder Pressure: Past, Present, and Future ASME Journal of Dynamic Systems, Measurement, and Control 115 343 350 1993
- Rassweiler M.G. Withrow L. Motion Pictures of Engine Flames Correlated with Pressure Cards SAE 800131 1980
- Rizzoni G Estimate of Indicated Torque from Crankshaft Speed Fluctuations: A Model for the Dynamics of the IC Engine IEEE Transactions on Vehicular Technology 38 3 168 179 1989
- Schmitt G. Stability Analysis of Nonlinear Multivariate Feedback Systems with the Off-Axis Circle Criterion Automatisierungstechnik AT 6 270 276 1999
- Shiao Y. Moskwa J.J. Misfire Detection and Cylinder Pressure Reconstruction for SI Engines SAE 940144 1994
- Shiao Y Moskwa J.J. Cylinder Pressure and Combustion Heat Release Estimation for SI Engine Diagnostics Using Nonlinear Sliding Observers IEEE Transactions on Control Systems Technology 3 1 70 78 1995
- Wagner M. Böhme J.F. In-Cylinder Pressure Estimation form Structure Borne Sound SAE 2000-01-0930 2000