This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Springback Determination By Springback Index Approach
Technical Paper
2005-01-0086
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
A new mechanical parameter, Springback Index (SBI), is proposed to reflect the magnitude of sheet-metal springback at a given flow stress level. Through conducting Tension-Unloading-Reloading (TUR) tests and measuring the Effective Unloading Modulus (EUM) Parameter, which is defined as the ratio of the non-linear recovery vs. total recovery, SBI can be determined for the sheet metal after complex forming processes.
To verify this SBI approach, U-free bending tests are conducted with galvanized and galvannealed DP600 sheet steels. The results indicate that the determination of SBI is remarkably simplified and the accuracy of springback prediction is significantly improved.
Recommended Content
Authors
Citation
Sun, S., Ma, H., and Wang, Z., "Springback Determination By Springback Index Approach," SAE Technical Paper 2005-01-0086, 2005, https://doi.org/10.4271/2005-01-0086.Also In
References
- Gardiner F. J. The spring back of Metals Trans. ASME 79 1 1958
- Johnson J. Xu T. X. Springback after the biaxial elastic-plastic pure bending of a rectangular plate Int. J. Mech. Sci. 23 619 1981
- Tozawa Y. Forming technology for raising the accuracy of sheet-formed products J. Mater. Proc. Tech. 22 343 1990
- Karafillis A. P. Boyce M. C. Tooling design in sheet metal forming using springback calculations Int. J. Mech. Sci. 34 2 1992
- Cleveland R. M. Ghosh A. K. Inelstic effects on springback in metals Int. J. Plasticity 18 2002
- Li K. P. Carden W. P. Wagoner R. H. Simulation of springback Int. J. Mech. Sci. 44 2002
- Carden W. D. Geng L. M. Matlock D. K. Wagoner R. H. Measurement of springback Int. J. Mech. Sci. 44 2002
- Yoshida F. Uemori T. Fujiwara K. Elatic-plastic behavior of steel sheets under in-plane cyclic tension-compression at large strain Int. J. Plasticity 18 2002
- Nishino S. Ohya K. Naruishi K. Proposal for reducing press working load and highly accurate evaluation of springback error in bending automobile sheet metal JSAE Review 24 2003
- Geng L. Wagoner R. H. Springback analysis with a modified hardening model Sheet Metal Forming: Sing Tsng 65 th Anniversary Volum, SAE SP1536 2000 2000-01-0768
- Zhu H. Huang L. Wong C. Unloading modulus on springback in steels, Sheet/Hydro/Gas forming technology and modeling SAE SP1840 2004 2004-01-1050
- Samuel M. Experimental and numerical prediction of springback and side wall curl in U-bendings of anisotropic sheet metals J. Mater. Proc. Tech. 105 2000
- Sowerby R. Uko D. K. A review of certain aspects of the Bauschinger effect in metals Mater. Sci. & Eng. 41 43 1979
- Chun B. K. Jinn J. T. Lee J. K. Modeling the Bauschinger effect for sheet metals, part I: theory Int. J. Plasticity 18 2002
- Erdogan M. Priestner R. Effect of martensite content, its dispersion, and epitaxial ferrite content on Bauschinger behavior of dual phase steel Mater. Sci. & Tech. 18 04 2002