This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
The Study of Particle Number Reduction Using After-Treatment Systems for a Heavy-Duty Diesel Engine
Technical Paper
2004-01-1423
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
To reduce ultra fine particle number concentration from a heavy-duty diesel engine, the effects of diesel fuel property and after-treatment systems were studied. The reduction of ultra fine particle number concentration over steady state mode using an 8 liter turbocharged and after-cooled diesel engine was evaluated. PM size distribution was measured by a scanning mobility particle sizer (SMPS). The evaluation used a commercially available current diesel fuel (Sulfur Content: 0.0036 wt%), high sulfur diesel fuel (Sulfur Content: 0.046 wt%) and low sulfur diesel fuel (Sulfur Content: 0.007 wt%). The after-treatment systems were an oxidation catalyst, a wire-mesh type DPF (Diesel Particle Filter) and a wall-flow type catalyzed DPF. The results show that fine particle number concentration is reduced with a low sulfur fuel, an oxidation catalyst, a wire-mesh type DPF (Diesel Particulate Filter) and wall flow type catalyzed DPF, respectively. The wall flow type catalyzed DPF was the most effective for the particle reduction. The particle number reduction efficiency of the wall flow type DPF was 97% in the range of 50 to 70 nm mobility diameter over steady state mode.
Recommended Content
Authors
Topic
Citation
Hosoya, M., Shundo, S., and Shimoda, M., "The Study of Particle Number Reduction Using After-Treatment Systems for a Heavy-Duty Diesel Engine," SAE Technical Paper 2004-01-1423, 2004, https://doi.org/10.4271/2004-01-1423.Also In
Diesel Emissions on CD-ROM from the SAE 2004 World Congress
Number: SP-1835CD; Published: 2004-03-08
Number: SP-1835CD; Published: 2004-03-08
References
- International Commission on Radiological Protection “Human Respiratory Tract Model for Radiological Protection” Annals of the ICRP ICRP Publication 66 24 1-3 1994 Pergamon
- Abdul-Khalek I.S. Kittelson D.B. Brear F. “Diesel Exhaust Particle Size: Measurement Issues and Trends” SAE Paper 980525
- Ahlivik P. Ntziachristos L. Keskine J. Virtanen A. “Real Time Measurement of Diesel Particle Size Distribution with an Electrical Low Pressure Impactor” SAE Paper 98410
- Kasper M. Matter U. Burtscher H. Bukowiecki N. Mayer A. “NanoMet, a New Instrument for On-line Size-and Substance-Specific Particlate Emission Analysis” SAE Paper 2001-01-0216
- Maricq M,M. Chase R.E. Podsiadlik D.H. Vogt R. “Vehicle Exhaust Particle Size Distributions: A Comparison of Tailpipe and Dilution Tunnel Measurements” SAE Paper 1999-01-1461
- Abdul-Khalec I. Kittelson D. “The Influence of Dilution Condition on Diesel Exhaust Particle Size Distribution Measurements” SAE Paper 1999-01-1142
- Pagan J. “Study of Particle Size Distribution Emitted by a Diesel Engine” SAE Paper 1999-01-1141
- Sasaki S. Nakajima T. “Study on the Measuring Method of Vehicular PM Size Distribution to Simulate the Atmospheric Dilution Process” ,SAE Paper 2002-01-2716
- Raatz T. Mueller E. “Examination of Particle Size Distribution of Homogeneous and Conventional Diesel Combustion” SAE Paper 2001-01-3576
- Mogi H. Tajima K. Hosoya M. Shimoda M. “The Reduction of Diesel Engine Emissions by Using the Oxidation Catalyst of Japan Diesel 13 Mode Cycle” SAE Paper 1999-01-0471
- Mayer A. Czerwinski J. “Trapping Efficiency Depending on Particle Size” SAE Paper 960472
- Abdul-Khalec I. Kittelson D.B. “Diesel Trap Performance:Paricle Size Measurements and Trend” SAE Paper 982599