This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Disc Brake Lining Shape Optimization by Multibody Dynamic Analysis
Technical Paper
2004-01-0725
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
Improving the performance characteristics of a typical disc brake encompasses a number of design strategies as well as limitations imposed by cost objectives. Utilizing pad loading uniformity in a design is one strategy that offers an improvement in desired performance characteristics, including a reduction in tapered lining wear as well as a possible reduced propensity for noise generation. To approach this design strategy, a procedure has been developed to tailor the brake pad lining profile to maximize pad loading uniformity in a multibody dynamics model of a typical disc brake. In determining an optimal lining configuration, a suitable compromise for gaining beneficial performance improvements in a cost effective manner is reached.
The implementation of this design strategy involves the parametric definition of the lining profile by introducing a series of variables that are linked to the profile markers. These variables can be used to conduct a sensitivity analysis, design of experiments, or an optimization to investigate factors that affect pad loading characteristics. Furthermore, this approach has the flexibility to allow for additional constraints, including pad wear and the ability to generate a lining profile for a desired pad loading distribution. An optimization was conducted to minimize pad load standard deviation, where the variables that define the lining profile are considered as design variables. The optimal profile results are contrasted with the baseline, showing a good percent reduction in pad force standard deviation under the given operating conditions for the inboard and outboard pads.
Recommended Content
Technical Paper | Lining Selection with Surrogate Brakes |
Technical Paper | From Prototype to Production - The Practical Nature of Brake Squeal Noise |
Technical Paper | Interface Pressure Distributions Through Structural Modifications |
Authors
Citation
Penninger, C. and Swift, R., "Disc Brake Lining Shape Optimization by Multibody Dynamic Analysis," SAE Technical Paper 2004-01-0725, 2004, https://doi.org/10.4271/2004-01-0725.Also In
ABS/TCS, Brake Technology and Foundation Brake NVH, and Tire and Wheel Technology
Number: SP-1866; Published: 2004-03-08
Number: SP-1866; Published: 2004-03-08
SAE 2004 Transactions Journal of Passenger Cars: Mechanical Systems
Number: V113-6; Published: 2005-07-05
Number: V113-6; Published: 2005-07-05
References
- Vanderplaats, G. N. “Structural Design Optimization Status and Direction,” Journal of Aircraft 36 1 February 1999
- Maxwell, C. Scientific Papers 2 Dover, New York 1952 175 177
- Mitchell, A. G. M. “The Limits of Economy of Material in Frame Structures “Philosophical Magazine,” 8 47 1904 589 597
- Suryatama, D. Bernitas, M. M. Budnick, G. F. Vitous, W. J. “Simultaneous Topology and Performance Redesign by Large Admissible Perturbations for Automotive Structural Design,” SAE 2001 World Congress (SAE 2001-01-1058 )
- Swift, R. “A Parametric Modeling Approach for the Preliminary Design of Automotive Disc Brakes,” 22 nd SAE Brake Colloquium (SAE- 2003-01-3330 )
- Fieldhouse, J. “A Proposal to Predict the Noise Frequency of a Disc Brake Based on the Friction Pair Interface Geometry,” 17 th SAE Brake Colloquium (SAE 1999-01-3403 )
- Liu, W. Pfeifer, J. “Reducing High Frequency Disc Brake Squeal by Pad Shape Optimization,” SAE 2000 World Congress (SAE 2000-01-0447 )
- Hohnman, Ch. Schiffner, K. “Pad Wear Simulation Model,” 17 th SAE Brake Colloquium (SAE 1999-01-3392 )
- El-Butch, A. Ibrahim, I. “Modeling and Analysis of Geometrically Induced Vibrations in Disc Brakes Considering Contact Parameters,” (SAE 1999-01-0143 )
- MSC - ADAMS User's Manual 2003 MSC Corporation