This content is not included in
your SAE MOBILUS subscription, or you are not logged in.
Mechanical Degradation of Viscosity Modifiers in Heavy Duty Diesel Engine Lubricants in Field Service
Technical Paper
2003-01-3223
ISSN: 0148-7191, e-ISSN: 2688-3627
Annotation ability available
Sector:
Language:
English
Abstract
Modern multi-grade engine lubricants are formulated to “stay in grade” during field service. Viscosity loss during the early stages of lubricant life is commonly believed to be caused by mechanical degradation of the viscosity modifier in the engine [1]. The Kurt Orbahn shear stability bench test (ASTM D 6278, 30 cycles) has been the industry standard predictor of viscosity loss due to polymer shear in heavy duty diesel engine lubricants. However, the Engine Manufacturers' Association (EMA) has expressed some concern that it underestimates the degree of polymer shear found in certain engines in the field, such as the Navistar 6.0L HEUI (Hydraulic Electronic Unit Injector) Power Stroke engine; a more severe bench test would serve to improve correlation with this and other similar engine designs.
This paper offers a new approach for critically examining the relationship between the bench test and field performance. Rather than indirectly measuring polymer shear via viscosity determination, a method for directly measuring olefin copolymer (OCP) molecular weight in heavy duty diesel drain oils was developed. The main advantage of this approach is that we can follow the polymer degradation process that occurs near the end of the oil drain period, when the accumulation of soot and/or oxidation by-products masks changes taking place to the polymer that could be affecting viscosity.
Over sixty drain oils taken from a large variety of commercial truck engines were analyzed. In addition, a mathematical model was developed to quantify the relative effects of polymer shear and soot accumulation on the kinematic viscosity of used engine oil, assuming no oxidative thickening mechanism. This study shows that (1) the standard ASTM D 6278 test adequately predicts OCP molecular weight break-down in many modern diesel engine lubricants, but (2) certain engine designs (such as the HEUI fuel injection system) and/or duty cycles degrade polymers to a level near that achieved in the 90-cycle Kurt Orbahn bench test.
Recommended Content
Authors
Citation
Covitch, M., Wright, S., Schober, B., McGeehan, J. et al., "Mechanical Degradation of Viscosity Modifiers in Heavy Duty Diesel Engine Lubricants in Field Service," SAE Technical Paper 2003-01-3223, 2003, https://doi.org/10.4271/2003-01-3223.Also In
References
- Herbeaux, J-L. Flamberg A. Koller R.D. VanArsdale W.E. “Assessment of Shear Degradation Simulators,” SAE Tech. Paper Ser. No. 982637 1998
- Huggins, M.L. J. Am. Chem. Soc. 64 2716 1942
- Billmeyer, F.W. Jr. Textbook of Polymer Science 83 John Wiley & Sons 1966
- Hillman, D.E. Morris P.R. Paul J.I. Pickles D. “Comparison of the Modes of Degradation of Viscosity Index Improvers in the Kurt Orbahn and FZG Tests by Gel Permeation Chromatography,” Institute of Petroleum Report IP 77 - 008 1977
- Covitch, M.J. “How Polymer Architecture Affects Permanent Viscosity Loss of Multigrade Lubricants,” SAE Tech. Paper Ser. No. 982638 1998
- Covitch, M.J. Humphrey B.K. Ripple D.E. “Oil Thickening in the Mack T-7 Engine Test - Fuel Effects and the Influence of Lubricant Additives on Soot Aggregation,” SAE Tech. Paper Ser. No. 852126 1985
- Brandrup, J. Immergut E.H. Polymer Handbook John Wiley & Sons 1975
- Crespi, G. Valvassori A. Flisi U. “Olefin Copolymers,” Stereo Rubbers 365 431 1977
- LaRiviere, D. Asfour A-F.A. Hage A. Gao J.Z. “Viscometric Properites of Viscostiy Index Improvers in Lubricant Base Oil over a Wide Temperature Range. Part I: Group II Base Oil,” Lub. Sci. 12-2 133 143 2000
- Rubin, I.D. Sen A. “Solution Viscosities of Ethylene-Propylene Copolymers in Oils,” J. Appl. Polym. Sci. 40 523 530 1990
- Rubin, I.D. Kapuscinski M.M. “Viscosities of Ethylene-Propylene-Diene Terpolymer Blends in Oil,” J. Appl. Polym. Sci. 49 111 1993
- Rubin, I.D. “Polymers as Lubricant Viscosity Modifiers,” Polym. Preprints, Am. Chem. Soc. Div. Poly. Chem. 32 2 84 1991
- Rubin, I.D. Stipanovic A.J. Sen A. “Effect of OCP Structure on Viscosity in Oil,” SAE Tech. Paper Ser. No. 902092 1990
- Kapuscinski M.M. Sen A. Rubin I.D. “Solution Viscosity Studies on OCP VI Improvers in Oils,” SAE Tech. Paper Ser.No. 892152 1989
- Kucks, M.J. Ou-Yang H.D. Rubin I.D. “Ethylene-Propylene Copolymer Aggregation in Selective Hydrocarbon Solvents,” Macromol. 26 3846 1993
- Sen, A. Rubin I.D. “Molecular Structures and Solution Viscosities of Ethylene-Propylene Copolymers,” Macromol. 23 2519 1990
- Ramakumar, S.S.V. Kagdiyal V. Tiwari O.P. Chopra A. Rao A.M. Sarpal A.S. Bhatnagar A.K. “Degradation Pattern of Polymeric Viscosity Index Improvers in Cross-Graded Engine Lubricants,” SAE Tech. Paper Ser. No. 2001-28-0038 2001
- McGeehan, M.A. et. al “The World's First Diesel Engine Oil Category for Use with Low-Sulfur Fuel: API CG-4,” SAE Tech. Paper Ser. No. 941939 1994